|
2 a-5 problems |
Post Reply 
|
| Author | |
teamsouth 
Member 
Joined: 03 January 2006 Status: Offline Points: 9 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: 2 a-5 problemsPosted: 31 December 2006 at 2:51pm |
|
i have 3 a-5's set up identical. 1 shoots great the other 2 make soup and i cant figure it out. heres what donr to them cyclone mods: velocity mod and lightning mod was boards qev's e grip(obviously) jcs double trgger polished internals madman spring kist updated rear bolt high pressure reg (palmer) for the life of me i cant figure out what is going on with these 2 guns any help appreciated |
|
 |
|
|
Snake6
Platinum Member 
Outranked by guitarguy? Joined: 11 September 2003 Location: United States Status: Offline Points: 11229 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 December 2006 at 2:56pm |
|
Need more info.
|
|
|
|
|
|
|
teamsouth
Member
Joined: 03 January 2006 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 December 2006 at 3:08pm |
|
put air into it and just sprays out broken paint. cyclone is full of paint and so is the internals. hpr on 1 gun is @ 600 the other is @ 800 and they both have been at every pressure in between. once in a while theyll shoot 5-10 good balls and then break the next 20. Im jut disgusted with this. Chris |
|
|
|
|
Snake6
Platinum Member
Outranked by guitarguy? Joined: 11 September 2003 Location: United States Status: Offline Points: 11229 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 December 2006 at 3:22pm |
|
Using CO2 or HPA?
|
|
|
|
|
|
|
|
teamsouth
Member
Joined: 03 January 2006 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 December 2006 at 5:42pm |
|
4500 psi hpa..and come to mention that it goes through air like there is no tomorrow..and it doesnt leak anywhere by the way thanks for the help so far Edited by teamsouth - 31 December 2006 at 5:52pm |
|
|
|
|
tallen702
Moderator Group 
Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11857 |
Post Options
Thanks(0)
Quote Reply
Posted: 01 January 2007 at 9:25pm |
|
Well, without LPK's they're going to go through a ton of air no matter what you do, until you lower the operating pressure, they're going to eat it up faster than an un-modded Matrix.
It sounds like you are definitely chopping paint if it's all the way up in the feeder. I'd take a look and make sure that the cyclone is syncing up with the rest of the firing cycle of the A-5. That's about the only thing I can think of outside of either shooting crappy paint or it being too cold outside and it's breaking because it is brittle. |
|
|
<Removed overly wide sig. Tsk, you know better.>
|
|
|
|
|
teamsouth
Member
Joined: 03 January 2006 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 January 2007 at 5:20pm |
|
Ok..Not to sound totally stupid, but how am i going to check that it is sync with the rest of the mechanism?
|
|
|
|
|
tallen702
Moderator Group
Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11857 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 January 2007 at 5:52pm |
|
take off the hopper, fire the marker without any paint in it (take the barrel off as well so you get more light in the chamber) and watch the cyclone feeder and the bolt through the feeder itself. This way you can see if the feeder is feeding at approximately the same time and rate. OR you can buy some re-ball (rubber .68 cal balls) turn down your velocity so you don't put a hole through a pillow or something, and see if you have any issues, if the cyclone and the bolt aren't synced and you are indeed chopping paint, then the marker will jam when it hits the re-ball.
|
|
|
<Removed overly wide sig. Tsk, you know better.>
|
|
|
|
|
teamsouth
Member
Joined: 03 January 2006 Status: Offline Points: 9 |
Post Options
Thanks(0)
Quote Reply
Posted: 02 January 2007 at 6:56pm |
|
ill have to give it a try..its killin me that 2 guns dont shoot for sh...........it and 1 is awsome Now lets say its not in sync.. Guess ill be going for a new cyclone? Or lets say the opposite..it is in sync.. then what to?
thanks for the help Edited by teamsouth - 02 January 2007 at 7:24pm |
|
|
|
|
ekeboo
Gold Member 
strike 1 5/1 Filter dodge Joined: 23 May 2004 Location: United States Status: Offline Points: 1394 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 January 2007 at 4:01pm |
|
Tallen has a good idea there. It sounds like something with your cyclone take off the QEVs for a little while and see if it makes a difference |
|
 
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options