|
Chopping a lot of balls |
Post Reply 
|
| Author | |
Joopie 
Member 
Joined: 20 February 2004 Location: Netherlands Status: Offline Points: 26 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Chopping a lot of ballsPosted: 21 February 2005 at 6:14am |
|
Heey, Yesterday on the field it was one big mess. I sprayed al over the place. My A-5 chopped one ball after the other. I took it appart and looked in the cyclone feed. It got paint everywere. But there is no wearing of the materials. They all looked good. The feed screw was not to tightend. The output pressure of my HPA bottle is 800 psi. My rear spring is not worn. I have installed the updates for the cyclone. My setup was E-grip set on semi ROF screw turned to max, JCS Duel trigger, HPA, 32* night styk and I used the stock barrel. The paint was new Draxxus midnight and blaze. I've searched on this forum and I found out there is almost no chance to outshoot the Cyclone feed. But why did I spayed then? Hope you guy's van help me,
Dominick
Edited by Joopie |
|
 |
|
|
LordJovian
Member
Joined: 01 June 2004 Location: United States Status: Offline Points: 1882 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 February 2005 at 8:32am |
|
Bad paint? It takes only one to break to screw up the cyclone. Also cold weather can screw up paint when it sits out for too long.
|
|
|
A-5
E-grip Chipley Custom Carbon Graphite 16" Evil Adapter(Spyder) 32 Deg New '03 XChamber Remote Line Gun Sling Sniper f/x Stock LPK 68/4500 HPA R-5 CP Reg JCS Duel Trigger |
|
|
|
|
Juan Hernandez
Member
Joined: 04 July 2003 Location: United States Status: Offline Points: 74 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 February 2005 at 12:24pm |
|
yea and watch where u keep ur paint the humidity has to be around 50 to 60% also it could be that ur velocity is really high.but i dont think it should chop balls even if it is high i think its ur paint
|
|
|
Juan Hernandez
|
|
|
|
|
Joopie
Member
Joined: 20 February 2004 Location: Netherlands Status: Offline Points: 26 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 February 2005 at 2:55pm |
|
My velocity was 245 fps. It might be the paint, but I bought it yesterday. Greetz, Dominick |
|
|
|
|
Stormcharger
Member
Joined: 10 September 2004 Location: United States Status: Offline Points: 394 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 February 2005 at 7:36pm |
|
Did you check to see how long the paint was sitting on the shelf at the store? Even the best premium paint will settle as it sits on the shelf. Get into the habit of actually looking at your paint before putting it in your gun.
|
|
|
|
|
The_Sniper
Member
Spiderman’s my cuz- ok, you can touch me Joined: 08 December 2003 Location: United States Status: Offline Points: 423 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 February 2005 at 9:34pm |
|
Were you playing in the cold? The cold does evil to paint.
|
|
|
My PB Stuff.
Tippmann 98 Coustom M4 Stock M4 Style top sights Romote coiled hose G2K Richochet hopper 4-1 pod holder 3x 20 once tanks PMI Themeral mask JT Full Protection goggle system |
|
|
|
|
Joopie
Member
Joined: 20 February 2004 Location: Netherlands Status: Offline Points: 26 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 February 2005 at 2:18am |
|
Well, it was a little cold. But other players didn't had this problem, paint breaking because of the cold. So it's most likely the paint. Some players did said it already, but I didn't believe them. The paint does indeed look a little bit old. That's a relief for me that it isn't the A-5. Thanks for the reply's people, Greets, Dominick |
|
|
|
|
MassDriver
Member
Joined: 30 November 2003 Location: United States Status: Offline Points: 125 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 March 2005 at 11:05pm |
|
I had a lot of problems with too small of a barrel bore size.
were they barrel bursts or was the bolt actually chopping the ball?
|
|
|
My Gun:
Angel 4 Fly Halo B 68/4500 DynaFlow Dye Ultralite |
|
|
|
|
Mad Psience
Member
Strike 2 - Flaming Joined: 06 February 2005 Location: Canada Status: Offline Points: 312 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 March 2005 at 1:40am |
|
if you have a comp air kit installed 800psi is overkill. don't they operate around 400-450 psi ? check that. I don't think small bore is your problem, most flatline users use it consistantly. |
|
|
|
|
|
|
whoknowswho
Member
Joined: 08 September 2004 Location: United States Status: Offline Points: 411 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 March 2005 at 1:36pm |
|
If you don't clean your barrel well after you play, junk can get stuck inside that won't come out through shooting. Little bits of shell can stick inside it and shred your paint. If you let it sit, it takes a lot of work to get it out. Hold your barrel up to the light when it is clean and look throught it. If it is dull or you see debris inside clean it well with alcohol until shiny.
|
|
|
|
|
Jochen
Member
Joined: 09 April 2003 Location: United States Status: Offline Points: 416 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 March 2005 at 3:05pm |
|
Two things -
First - I've shot Blaze through the A5 flatline and it works great, but the midnight would be a paint that i would avoid with a Tippmann marker. Second - How old is the battery in your Egrip? The timing could be off with the bolt and the cyclone enough to chop the balls. I'd try a new battery and fire some paint through it again to test. Jochen Edited by Jochen |
|
|
Team Identity Crisis
|
|
|
|
|
StandingCow
Member
Joined: 27 February 2005 Location: United States Status: Offline Points: 5 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 March 2005 at 5:44pm |
|
I have been hearing that sharp edges in the cyclone feed could cause this also... If I have any ball chopping problems Im gonna try and round the edges of the cyclone with a file.. |
|
|
|
|
|
|
brutl_force
Gold Member 
One Truck’n Machine! Joined: 18 August 2002 Location: United States Status: Offline Points: 1887 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 March 2005 at 6:37pm |
|
NO FILE!!!!!!!! Use 600 grit sand paper!! But only polish the metal parts that the ball toutches, unless you find a burr on the plastic. While you are at the hardware store, get a can of "Teflon dry lube" by "Blasters" I think. That will put dry teflon on plastic, metal, anyting on a paintball gun. Spray some of that onto all exterior parts of the cyclone, and spray the inside of a well cleaned, dry barrel (other than a flatline). That will help a lot.
brutl |
|
|
Inclementia Vigor (Translated from latin to brutal force). And yes, I spell "brutl" wrong on purpose.
|
|
|
|
|
ac600ccer
Member
Joined: 20 August 2002 Location: United States Status: Offline Points: 437 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 March 2005 at 7:24pm |
|
I tryed to play this last weekend to,it was about 40 (f)degrees outside. I had my egrip on turbo,with the rof at about half way. the first 5 or 6 balls had no problem with.but after that forget it. so I cleaned up everything, lowered my fps(250) put my grip on semi auto,turned rof all the way down,still the same thing. paint was from the end of last season(nov 04). other plp were useing timmys,and cokers,they had no problems,so i to hope it was just to cold for my tippy to shoot.
|
|
|
my A-5 setup,sp freak kit,pro-seal powertube,E-grip,cp 45* drop,polished internals,GTA lpk,palmers fatty stab.crossfire 45/4500 ,dye rhino cover,jcs duel trigger
|
|
|
|
|
ChuckNasty13
Member
Joined: 14 March 2005 Location: United States Status: Offline Points: 29 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 March 2005 at 6:07pm |
|
ive shot midnight through my 98 a lot and in my appinion its the best
winter paint ive ever used and from what other pplhave said the blaze isnt bad so i dont think that its the paint tats ur problem |
|
|
Chuck Nasty of the NY Headrush
headrush.com |
|
|
|
|
98c Dude13
Member
Joined: 18 June 2004 Location: United States Status: Offline Points: 2082 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 March 2005 at 4:54pm |
|
Maybe because you chopped one ball because it was egged then the other balls got covered with paint then got all in your barrel then you chopped.
|
|
|
TIPPMANN 98 CUSTOM
14" Progressive barrel 32* Black gel grips BT-16 Double trigger Pen Spring Mod X-core Expansion Chamber Vertical Adapter |
|
|
|
|
EagleKeeper173
Member
Joined: 16 March 2005 Location: United States Status: Offline Points: 16 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2005 at 2:26am |
|
http://www.tippmann.com/players/forum/wwf77a/forum_posts.asp ?TID=128601&PN=1 read my reply to that thread. Sorry if that isn't the prob... |
|
|
need timmy
|
|
|
|
|
a5 user
Member
Joined: 17 March 2005 Location: Canada Status: Offline Points: 1 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2005 at 10:34pm |
|
hey i got an a5 with flatline barerel. i went out paintballin todday and it was choping balls
what could be the reson? it wasnt cold @ all and i was using ghetto balls...... i kept having to squegee it after about 15 shots. my velocity adjuster was only out about two or three threads... what could it be? |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options