It's Alive! [updated with video on page 2!] |
Post Reply | Page 12> |
Author | |
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
Posted: 19 April 2009 at 1:40am |
Igor, throw the switch!
Obviously there's a metric butt-load of aesthetic work to be done. I'm also waiting for the eyes to arrive. As of now, she cycles. I also need to insulate the board. If I tighten down the grip frame screws to hand-tight, the board shorts. Edited by tallen702 - 05 August 2011 at 4:29pm |
|
merc
Platinum Member American Scotchy Joined: 10 June 2002 Location: VA, USA Status: Offline Points: 7112 |
Post Options
Thanks(0)
|
sexi, you gunna modify a grip to hold a battery?
|
|
saving the world, one warship at a time.
|
|
sinisterNorth
Moderator Group 1 strike, language, 10/3 Joined: 30 May 2004 Location: PA Status: Offline Points: 10463 |
Post Options
Thanks(0)
|
Very cool. I can't wait to see it finished.
|
|
Pumpker'd; (V.) When a pump player runs up and shoots you at point blank range because you thought 20bps made you good.
|
|
GOMEZ15
Member Joined: 29 March 2009 Location: New Mexico Status: Offline Points: 124 |
Post Options
Thanks(0)
|
wow that will be a cool mod
|
|
FORUM snowboarding
|
|
merc
Platinum Member American Scotchy Joined: 10 June 2002 Location: VA, USA Status: Offline Points: 7112 |
Post Options
Thanks(0)
|
dude, did you fill in the gills? ...
|
|
saving the world, one warship at a time.
|
|
oldpbnoob
Platinum Member Not old, Not noob. May be Dave's grandma Joined: 04 February 2008 Location: Yankee Stadium Status: Offline Points: 5676 |
Post Options
Thanks(0)
|
Burn the Witch!! Edited by oldpbnoob - 19 April 2009 at 5:34pm |
|
High Voltage
Platinum Member Fire in the disco Joined: 12 March 2003 Location: 127.0.0.1 Status: Offline Points: 14179 |
Post Options
Thanks(0)
|
Not the third switch!? |
|
|
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
I did mill off the gills. But never fear. I've got another original 98 in pristine condition with a nice silver-to-black fade job on it with gills intact.
They're milled off so that later, I can run with a dmlcd style breech to shorten the overall length. Yes, for now the battery will be housed in the fore grip. Anyway, it's going to take some major tuning to get it to shoot fully. right now it cycles, but it's too short. I'll have to re-work the forward and rearward pulse numbers. I'm also going to eventually run a 4-way solenoid and 2-way the ram. For now, it's gonna be ghetto gunfighter time. Eyes came in yesterday btw. Will mill and place them soon enough. |
|
<Removed overly wide sig. Tsk, you know better.>
|
|
JohnnyCanuck
Moderator Group In soviet Canuckistan... Joined: 08 July 2004 Location: Canada Status: Offline Points: 1463 |
Post Options
Thanks(0)
|
Frankmann..awesome
|
|
Imagine there’s a picture of your favourite thing here.
|
|
merc
Platinum Member American Scotchy Joined: 10 June 2002 Location: VA, USA Status: Offline Points: 7112 |
Post Options
Thanks(0)
|
tallen you got access to a machine shop or u dremmeling the crap?
|
|
saving the world, one warship at a time.
|
|
choopie911
Moderator Group Commie Canuck Joined: 01 June 2003 Location: Canada Status: Offline Points: 30773 |
Post Options
Thanks(0)
|
I dont know how the hell you people figure this crap out. Videos are mandatory for this project.
|
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
Merc, Dremmel and a steady hand
Choop, I've gotta re-solder the solenoid connection and then I'll take photos/video of the whole shebang and post it. |
|
<Removed overly wide sig. Tsk, you know better.>
|
|
TinMan
Gold Member Joined: 10 October 2007 Status: Offline Points: 1003 |
Post Options
Thanks(0)
|
Center feed that beast.
Why the battery box when you did the foregrip battery mod?
|
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
Holy zombie tallen thread! Thought I'd look back through and see if I'd missed anything on this. Looks like I did. The battery box is where the solenoid is housed. The DMLCD board takes up the entirety of the grip frame due to the LCD screen. The Tippmann Effect version of the Matrix-98 hybrid pushed the solenoid to the front of the frame and forced the board out of the back of the frame. As a consequence, the grip frame had to be hacked in places which left the board exposed to the elements. I simply moved the solenoid to the battery box and routed the battery through the dead air chamber to the fore-grip. Since I was making it a "shorty" with the mini-cocker vertical adapter, I could use the stock foregrp panels to protect the battery terminal and battery from the elements. Eventually I'll hack that off and fashion a new battery box which will sit under the chamber just forward of the mini-cocker adapter allowing me to turn down the power-tube, shorten the bolt and ram stroke and shorten the whole project by about 2.5" I've got the wiring set up properly and found my cold short that was giving me issues with the on/off operation of the marker when the bolts were tightened down all the way in the grip frame and it now shoots beautifully even if it is a bit ghastly to look at. Once I get back from vacation, I'll shoot some video. I'm going to paint the whole thing this august after I take the time to mill channels in the exterior of the frame and install the anti-chop eyes and counter-sink the battery cable. I'll probably cover those with jb weld or the like and sand the finish down until you can't tell they're even there. I'm thinking a red-to-white fade/splash. I like to stand out. |
|
<Removed overly wide sig. Tsk, you know better.>
|
|
Monk
Moderator Group Joined: 23 October 2003 Location: United States Status: Offline Points: 6556 |
Post Options
Thanks(0)
|
OMG OLD BUMP hehehehe
Also... whats the conversion from Metric butt-load to SAE crap-load? |
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
SAE=1.61803399x(Metric/3.14159265) |
|
<Removed overly wide sig. Tsk, you know better.>
|
|
ShotFromAfar
Member Joined: 16 July 2009 Location: NY, Son! Status: Offline Points: 25 |
Post Options
Thanks(0)
|
No doubt ill get flamed for this but what exactly did you do? It looks like the most beast SMG for paintball I've ever seen!
|
|
You need some wine for that stunt |
|
TippmannLazEffect
Member Joined: 18 July 2009 Location: Connecticut Status: Offline Points: 27 |
Post Options
Thanks(0)
|
I would keep it looking ugly for a bit, especially if you play at a legit field.
Keep the guys thinking you have a pos and then own them on the field with it. "I also need to insulate the board. If I tighten down the grip frame screws to hand-tight, the board shorts." Even though I believe you said you fixed the issue, all I need was put a thin piece of plastic under the board which blocked any contact from the board to the metal of the frame. Great job and awesome replies to others questions A+ |
|
|
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
UPDATE!!!!!
Finally having time to work on this thing again after a 2 year hiatus, I have everything sorted, finishing the burying of the power cables, and am currently hollowing out the fore-grips to house the battery. I went back and used quick disconnects instead of hard solders for the splices, and had to make some modifications under the solenoid shroud to keep the LP line from kinking which caused poor cyclical performance. Now she runs like a beast! So, it's an original Tippmann E-Bolt ram, solenoid, and micro-switch coupled with a DMLCD board in an original Tippmann Model 98 body. I made the trigger magnetically returned with adjustable travel (set screw to make it short) The forward and back pulses are dead on for the ram, so she'll rip. All that's left to do is loop the lp from the solenoid to the ram so it doesn't crimp as easily, paint the hollowed out fore grip, bondo over the battery lines, and give it the final coats of sage green and clear coat and she's ready to go! |
|
Maiden Hell
Member Guested - Obscene material Joined: 22 July 2011 Location: Toronto Canada Status: Offline Points: 47 |
Post Options
Thanks(0)
|
Nice work, where did you learn how to do this?
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |