Stabilizer setup options?

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Howdy Y'all --   

I wanna get a Palmer Stablilizer, BUT I don't wanna replace the front grip-- I know alot of peeps use the vertical adapter then run a male stab up the front grip hole-

I also wanna keep my on/off, so I don' wanna replace my ASA with a female stab.

WHat I wuz thinking wood bee 2 either:

1. Run a male or direct stab vertically where the hose goes into the valve now.  I know I would havta modify the body, but I have seen a pic of this done and it looked kewl--

2. Or I could set up an inline stab on the bottom alongside my ASA - 

My main question is would either of these setups potentially hurt the marker?  I read somewhere that if u used method #1, if something hit the stab (like a  paintball?) that it could mess up the valve-??

I dont see how that could be- I mean, the LPKit offered by Tippmann uses that hole to put the Low Pressure Chamber on, so I dont see how a longer stab put there could hurt anything.

Any thoughts / ideas?

THANXABUNCH  

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
phreakshew Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 26 March 2003 Location: United States Status: Offline Points: 60	Topic: Stabilizer setup options? Posted: 04 June 2004 at 8:36pm
	Howdy Y'all -- I wanna get a Palmer Stablilizer, BUT I don't wanna replace the front grip-- I know alot of peeps use the vertical adapter then run a male stab up the front grip hole- I also wanna keep my on/off, so I don' wanna replace my ASA with a female stab. WHat I wuz thinking wood bee 2 either: 1. Run a male or direct stab vertically where the hose goes into the valve now. I know I would havta modify the body, but I have seen a pic of this done and it looked kewl-- 2. Or I could set up an inline stab on the bottom alongside my ASA - My main question is would either of these setups potentially hurt the marker? I read somewhere that if u used method #1, if something hit the stab (like a paintball?) that it could mess up the valve-?? I dont see how that could be- I mean, the LPKit offered by Tippmann uses that hole to put the Low Pressure Chamber on, so I dont see how a longer stab put there could hurt anything. Any thoughts / ideas? THANXABUNCH
	[IMG] http://www.paintballchat.net//hosting/phreakshew/TippmannOwnersP98.jpg ">

ReGuLaToR99 Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Joined: 29 October 2003 Location: United States Status: Offline Points: 1821	Posted: 04 June 2004 at 8:40pm
	i believe palmer makes some durable stuff and it wouldnt be able to be marketed if it was poor quality


phreakshew Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 26 March 2003 Location: United States Status: Offline Points: 60	Posted: 04 June 2004 at 9:08pm
	oh yeah-- Not concerned about the Palmer-- I yam kinda concerned about the 98's valve!
	[IMG] http://www.paintballchat.net//hosting/phreakshew/TippmannOwnersP98.jpg ">

fdjizm Members Profile Send Private Message Find Members Posts Add to Buddy List Member Guested - F-Bomb Joined: 02 May 2004 Status: Offline Points: 187	Posted: 05 June 2004 at 3:22am
	u dont have to modify the body to get the palmer in the slot where the hose goes u just screw it in like and ex-chamber, see the pic thats a palmers male.

DirtyDawg Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 28 April 2004 Location: United States Status: Offline Points: 38	Posted: 05 June 2004 at 7:22am
	phreakshew - got your PM. hope the info helps.
	Tippmann 98Custom - Parting out. PM me for parts availability 2k4 BKO Warsensor WS66 RIS Warsensor Zeus G1+

phreakshew Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 26 March 2003 Location: United States Status: Offline Points: 60	Posted: 06 June 2004 at 8:03pm
	thanx - ya it totally gives me more IDEAS!
	[IMG] http://www.paintballchat.net//hosting/phreakshew/TippmannOwnersP98.jpg ">

HeadHunter59 Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Dial down the center! Joined: 08 May 2003 Location: Milwaukee,WI Status: Offline Points: 2017	Posted: 06 June 2004 at 9:23pm
	ok here are some things you can do. Get the direct palmer that is where your hosue comes out of now and no if a paintball dose hit it. It wont get messed up. Now some info about palmers Palmer Stablizer--- The Stabilizer is a great regulator for Co2 or Nitrogen, and here?s why (copied from Palmers FAQ page): ?The major benefit of the Stabilizer over the UniReg is that the Stabilizer will maintain consistency just about twice as well as the UniReg can. This is due to the design and dimensioning of the unit. Through any regulator there is a certain amount of inverse pressure variation in the output pressure that results from the variation in supply pressure. (as the supply pressure to the regulator goes up or down, the output pressure will go up or down, exactly opposite, and in a ratio that is proportional to the valve and diaphragm (or plunger) dimensions. (i.e. as the supply pressure goes down, the regulated pressure will go up slightly and vice-versa) In the case of a UniReg, that ratio of change is approx. 35:1; meaning that for every 35 psi of supply pressure change, the output pressure will vary approx. 1 psi. The Stabilizer will only vary about 1/2 as much. In other words, the Stabilizer is rated as a 70:1 regulator, in that it takes a 70 psi change in supply pressure to yield a 1 psi change in output pressure.? The Stabilizer is also adjustable from 0-900psi. This regulator will cost anywhere from $65-$95, depending on which setup of the Stabilizer you choose, and it can be found at Palmer-Pursuit