|
P/C steel hose length? |
Post Reply 
|
| Author | |
Panda Man 
Platinum Member 
I’ll feed you to my SNAKE!! METALFACE!! Joined: 25 July 2004 Location: Neutral Zone Status: Offline Points: 10605 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: P/C steel hose length?Posted: 07 October 2004 at 11:08am |
|
I Need to know the length of steel-braided hose I'll need for. --------------------------------------- Ex-Chamber: Dead on. 8 Stage X-core ASA: Dead on. Universal Drop. and (2) 90* Fittings --------------------------------------- Note: I've looked on county's Hose Chart but no one had this sort of set-up. Note*: I dont want to use Macro/Microlines but if its less then what county sells then I'll have to deal with using Macro. Edited by Panda Man |
|
|
|
 |
|
|
County
Gold Member 
Most Favored Nation Status Joined: 10 June 2002 Location: United States Status: Offline Points: 1833 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 October 2004 at 7:42am |
|
With that setup, you'll need a really short hose (which is almost impossible to work with) or you'll have to use a longer hose and rainbow it.
If you use macroline, put a regular 90-degree connector elbow in the bottom of the x-core. Then, you can use the macroline kit with two 90-degree macroline fittings to get a straight line. |
|
|
|
|
PopeMobile
Member 
Guested - Complete idiot Joined: 07 October 2004 Status: Offline Points: 197 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 October 2004 at 8:07am |
|
Why dont you buy 500 feet of braided cable then go from there. because buying an excessive amount of steel braided cable is like buying the excessing amount of pointless stuff for youre gun that you did.
|
|
|
To the pope mobile!!
|
|
|
|
|
Panda Man
Platinum Member
I’ll feed you to my SNAKE!! METALFACE!! Joined: 25 July 2004 Location: Neutral Zone Status: Offline Points: 10605 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 October 2004 at 9:17am |
|
^ good point. I knew that connection was going to be extremly short. Meh oh well. I'll just use macroline |
|
|
|
|
|
|
|
County
Gold Member
Most Favored Nation Status Joined: 10 June 2002 Location: United States Status: Offline Points: 1833 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 October 2004 at 9:38am |
|
With macroline I've always been fine if it's in a straight line. It's when people try to bend it that we usually have problems. Bending the macroline causes kinks and weak spots.
|
|
|
|
|
Panda Man
Platinum Member
I’ll feed you to my SNAKE!! METALFACE!! Joined: 25 July 2004 Location: Neutral Zone Status: Offline Points: 10605 |
Post Options
Thanks(0)
Quote Reply
Posted: 08 October 2004 at 10:22am |
|
^ Thats where all of my Hoses blow is at a curve. Well thanx for all your Help Mike. Edit: Hmmm... You think a Flame Drop forward would make it so that I could use Steel-braided? Edited by Panda Man |
|
|
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
. The only reason i dont want to use macro is because ive had bad experiences with it.