custom pro e LPK

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I just installed my GTA LPK on my new pro e it has about 2000 balls through her before this mod. i added a palmer regulator,RD blade trigger,pen spring mod,polished internals,macro line kit, when i gas it up with a full crossfire 92/4500 high pressure tank it keeps cycling when i pull the trigger the first time??? it kinda sounds like a response trigger when its out of gas? if i turn the pressure up on the reg to like 450-475 its fires and cycles fine? tippmann emailed me saying the LPK should run fine at 350-375 but i cant get the pressure that low? anyone else have these problems? any ideas? any help?

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
bigbadgixxer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 29 May 2005 Location: United States Status: Offline Points: 8	Post Options Post Reply Quote bigbadgixxer Report Post Thanks(0) Quote Reply Topic: custom pro e LPK Posted: 18 June 2005 at 9:35pm
	I just installed my GTA LPK on my new pro e it has about 2000 balls through her before this mod. i added a palmer regulator,RD blade trigger,pen spring mod,polished internals,macro line kit, when i gas it up with a full crossfire 92/4500 high pressure tank it keeps cycling when i pull the trigger the first time??? it kinda sounds like a response trigger when its out of gas? if i turn the pressure up on the reg to like 450-475 its fires and cycles fine? tippmann emailed me saying the LPK should run fine at 350-375 but i cant get the pressure that low? anyone else have these problems? any ideas? any help?

You Wont See Me Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Found in Big Al’s underwear drawer Joined: 02 December 2003 Location: Neutral Zone Status: Offline Points: 13335	Post Options Post Reply Quote You Wont See Me Report Post Thanks(0) Quote Reply Posted: 18 June 2005 at 10:44pm
	Could be a leak somewhere. Also, take out any home done mods and make sure thats not it. It shouldn't make a difference, but it wouldn't hurt to try. Unless you took off too much metal when polishing internals.
	A-5 E-Grip JCS Dual Trigger DOP X-CORE 8 stage x-chamber Lapco Bigshot 14" Beadblasted Optional setup: R/T Dead on Blade trigger

mike borra Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 20 April 2005 Status: Offline Points: 8	Post Options Post Reply Quote mike borra Report Post Thanks(0) Quote Reply Posted: 18 June 2005 at 10:51pm
	i polish the crap out of my internals and mine functions fine and i've had mine as low as 200 psi no joke. if your just shooting air that might be the problem as well because it needs back pressure to push the bolt back. if you haven't yet , put some paint through it.
	pain is only weakness leaving the body

98cowboy Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 07 August 2004 Location: United States Status: Offline Points: 464	Post Options Post Reply Quote 98cowboy Report Post Thanks(0) Quote Reply Posted: 18 June 2005 at 11:39pm
	Maybe your reg cant handle you high output tank when you drop it that low. Edited by 98cowboy
	GO BUCKS!!!

bigbadgixxer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 29 May 2005 Location: United States Status: Offline Points: 8	Post Options Post Reply Quote bigbadgixxer Report Post Thanks(0) Quote Reply Posted: 19 June 2005 at 10:13am
	the only homemade mod is the trigger pen spring. all else in marker is brand new? i have a palmer fatty LPR adjusted to 450 and it shoots fine. but i think it should be lower? tippmanns email also states that i need a high pressure tank to my low pressure reg? like i have.my local pro shop said it felt like the bolt was binding slightly in the power tube. when he adjusted it he could only get it too 550 to work? i took it apart sanded the tube got rid of all paint and burrs around where tube sat. then i got it down to 450 so i will shoot some paint through it today and see if it helps. palmer said about 2000 paintballs to break in spring assembly? will keep u guys posted. thanks tim

bigbadgixxer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 29 May 2005 Location: United States Status: Offline Points: 8	Post Options Post Reply Quote bigbadgixxer Report Post Thanks(0) Quote Reply Posted: 19 June 2005 at 12:44pm
	ran 4 halos through it and got the pressure down to 390 wierd? maybe it needed the paint i guess. well thanks for the help. tim

You Wont See Me Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Found in Big Al’s underwear drawer Joined: 02 December 2003 Location: Neutral Zone Status: Offline Points: 13335	Post Options Post Reply Quote You Wont See Me Report Post Thanks(0) Quote Reply Posted: 19 June 2005 at 1:58pm
	Your regulator needed to be broken in.
	A-5 E-Grip JCS Dual Trigger DOP X-CORE 8 stage x-chamber Lapco Bigshot 14" Beadblasted Optional setup: R/T Dead on Blade trigger

bigbadgixxer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 29 May 2005 Location: United States Status: Offline Points: 8	Post Options Post Reply Quote bigbadgixxer Report Post Thanks(0) Quote Reply Posted: 19 June 2005 at 8:31pm
	palmer emailed me and said about 2000 balls to break in the springs??? just telling u what they said to me? it works fine now pressure is around 390 consistent and my reg has a 92:1 ratio which i think is pretty good. tim