Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

What Should I Use
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
joetheman89 View Drop Down
Member
Member
Avatar

Joined: 14 January 2005
Location: United States
Status: Offline
Points: 92 		Post Options Post Options   Thanks (0) Thanks(0)   Quote joetheman89 Quote  Post ReplyReply Direct Link To This Post Topic: What Should I Use
    Posted: 07 August 2005 at 8:22pm
I need to stop a leak in a gun, should I use teflon tape or loctite around the threads. How would I use teflon tape or what type of loctite should I use. Thanks for you help!
98 Custom
Armson Stealth 13"
Flatline
GTA Expansion Chamber
GTA Double Trigger
Ben Tippmann Sealed Bolt
Lapco Drop
APP Sling
Back to Top
Mehs View Drop Down
Moderator Group
Moderator Group
Avatar
An Hero

Joined: 27 March 2004
Location: Neutral Zone
Status: Offline
Points: 3907 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mehs Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 8:51pm
Both do a good enough job, I personally think loctite is much easier.  Red could do fine, but if you ever plan to unscrew where ever it's leaking again, use blue, both work fine. 
[IMG]http://i27.tinypic.com/1538fbc.jpg">
Squeeze Box
☣
Back to Top
joetheman89 View Drop Down
Member
Member
Avatar

Joined: 14 January 2005
Location: United States
Status: Offline
Points: 92 		Post Options Post Options   Thanks (0) Thanks(0)   Quote joetheman89 Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:08pm
k, i would prolly have to use blue then, but exactly how do you use teflon tape, like do you put the sticky side on the thread,lol, i dont know
98 Custom
Armson Stealth 13"
Flatline
GTA Expansion Chamber
GTA Double Trigger
Ben Tippmann Sealed Bolt
Lapco Drop
APP Sling
Back to Top
CHAOSS View Drop Down
Member
Member
Avatar

Joined: 13 July 2005
Location: United States
Status: Offline
Points: 308 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CHAOSS Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:28pm
I think Enos posted somewhere how to use it correctly..he said something like cut off 1-2 inches, fold in half long ways, and wrap tightly starting at the top of the threads.
I myself used to think loctite until I tried it and it ran like water all over the place and I realized that my High pressure air compressor in the garage uses nothing but teflon tape for all the connections, but who knows maybe I bought some old loctite??
Back to Top
joetheman89 View Drop Down
Member
Member
Avatar

Joined: 14 January 2005
Location: United States
Status: Offline
Points: 92 		Post Options Post Options   Thanks (0) Thanks(0)   Quote joetheman89 Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:36pm
well do you fold the stick part together, when you fold it lengthwise? or fold it where the sticky stuff is on the outside, im confused,
98 Custom
Armson Stealth 13"
Flatline
GTA Expansion Chamber
GTA Double Trigger
Ben Tippmann Sealed Bolt
Lapco Drop
APP Sling
Back to Top
rossy11223 View Drop Down
Platinum Member
Platinum Member


Joined: 02 June 2005
Location: United States
Status: Offline
Points: 3435 		Post Options Post Options   Thanks (0) Thanks(0)   Quote rossy11223 Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:41pm

Quoted from Enos:

"Use teflon thread sealing tape to seal your hose fittings. I
prefer to tear off an inch and a half long piece, fold it in half
lengthwise, and then wrap it. Wrap CLOCKWISE around your fitting. And
try not to leave any tape hanging off the fitting, as it will tear off,
get blown up your air lines into your valve, and fulfill its purpose of
sealing something up. Except of course you dont WANT to seal the valve,
whoops!"
Back to Top
CHAOSS View Drop Down
Member
Member
Avatar

Joined: 13 July 2005
Location: United States
Status: Offline
Points: 308 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CHAOSS Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:49pm
Originally posted by joetheman89 joetheman89 wrote:

well do you fold the stick part together, when you fold it lengthwise? or fold it where the sticky stuff is on the outside, im confused,


Teflon tape has no sticky at all, its really smooth, thin plastic that fills the gaps in the threads
Back to Top
joetheman89 View Drop Down
Member
Member
Avatar

Joined: 14 January 2005
Location: United States
Status: Offline
Points: 92 		Post Options Post Options   Thanks (0) Thanks(0)   Quote joetheman89 Quote  Post ReplyReply Direct Link To This Post Posted: 07 August 2005 at 9:58pm
ok, thank-you for your help
98 Custom
Armson Stealth 13"
Flatline
GTA Expansion Chamber
GTA Double Trigger
Ben Tippmann Sealed Bolt
Lapco Drop
APP Sling
Back to Top
AdmiralSenn View Drop Down
Platinum Member
Platinum Member


Joined: 07 July 2002
Location: United States
Status: Offline
Points: 2683 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AdmiralSenn Quote  Post ReplyReply Direct Link To This Post Posted: 08 August 2005 at 9:58am
Ack. ALWAYS use Teflon tape. Loctite is NOT a sealer! It will hold your threads in place (great until you want to take a part off) but it will NOT make a pneumatic seal.

Plus Teflon tape is super easy to use. No drying at all and if you screw up you can peel it off pretty quickly.
Is God real? You'll find out when you die.

Okay, I don't have a clever signature zinger. So sue me.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.328 seconds.