New Flatline

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Hi, i just bought a flatline yesterday and installed it last night.
Quite Easy, until i loosened the front-top bolt too much and the thing
that pushes the front sight back up fell out and i had to take apart
the marker again. Just a few inquiries. 

1. The Button that you push to knock down the front sight is too
sticky. It will only pop back up when I put the hopper arm in and I
dont store the gun with it on(Bad for the feeding plastic part on the
hopper). Is there a way to loosen it so it is not as sticky?

2. The rear sight will not adjust properly. If i pull it out to an
extention length, it will fall back in the shroud to normal length. I
have tightened the rear bolt on the shroud as tight as I feel
comfterble and it still hangs loose. Shall I crack out the phillips and
tighten the other ones?

3. How much barrel should be poking out of the end of the shroud?

That is all. Help would be appreciated

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Nick E Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 04 May 2004 Location: Canada Status: Offline Points: 2	Post Options Post Reply Quote Nick E Report Post Thanks(0) Quote Reply Topic: New Flatline Posted: 07 August 2005 at 5:00pm
	Hi, i just bought a flatline yesterday and installed it last night. Quite Easy, until i loosened the front-top bolt too much and the thing that pushes the front sight back up fell out and i had to take apart the marker again. Just a few inquiries. 1. The Button that you push to knock down the front sight is too sticky. It will only pop back up when I put the hopper arm in and I dont store the gun with it on(Bad for the feeding plastic part on the hopper). Is there a way to loosen it so it is not as sticky? 2. The rear sight will not adjust properly. If i pull it out to an extention length, it will fall back in the shroud to normal length. I have tightened the rear bolt on the shroud as tight as I feel comfterble and it still hangs loose. Shall I crack out the phillips and tighten the other ones? 3. How much barrel should be poking out of the end of the shroud? That is all. Help would be appreciated

joetheman89 Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 14 January 2005 Location: United States Status: Offline Points: 92	Post Options Post Reply Quote joetheman89 Report Post Thanks(0) Quote Reply Posted: 07 August 2005 at 7:55pm
	For the number 1, I had that problem when I got mine, after a while it will fix it self, you have to use it for awhile, Number 2, just make sure you tighten the rear bolt as much as you can, thats all that will keep it to stay in place, Number 3, you must push the barrel as far as it goes into the adapter, I just use my hand and hammer it in, then it stops. Make sure the you line the barrel up correctly too Edited by joetheman89
	98 Custom Armson Stealth 13" Flatline GTA Expansion Chamber GTA Double Trigger Ben Tippmann Sealed Bolt Lapco Drop APP Sling

CHAOSS Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 13 July 2005 Location: United States Status: Offline Points: 308	Post Options Post Reply Quote CHAOSS Report Post Thanks(0) Quote Reply Posted: 07 August 2005 at 9:35pm
	#1= For mine I loosened the gun body bolt that is right under it about a half crank and it works fine now #3= from the tip of my barrel to the plastic shroud is 3 3/4 inches


Nick E Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 04 May 2004 Location: Canada Status: Offline Points: 2	Post Options Post Reply Quote Nick E Report Post Thanks(0) Quote Reply Posted: 07 August 2005 at 11:09pm
	Thanks, im good now, just that the rear bolt is tightened as much as it will go. It will stay all the way up or down, but none of the other positions.

AdmiralSenn Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Joined: 07 July 2002 Location: United States Status: Offline Points: 2683	Post Options Post Reply Quote AdmiralSenn Report Post Thanks(0) Quote Reply Posted: 08 August 2005 at 9:56am
	Just a tip for you: You may want to drill out the hole in the back of the shroud (just a tiny bit! stick drill bits in until you get one that ALMOST fits through) if it's sticky or hard to put the bolt through. I did that and it's a lot easier to put the Flatline on. The sight I had trouble with too, finally tightening it as I always had fixed it. Maybe it was the drilling that let it tighten a bit more than usual, I don't know.
	Is God real? You'll find out when you die. Okay, I don't have a clever signature zinger. So sue me.