|
Marker Won’t Recock |
Post Reply 
|
| Author | |
goats_896 
Member 
Joined: 24 October 2005 Location: United States Status: Offline Points: 70 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Marker Won’t RecockPosted: 10 November 2005 at 5:55pm |
|
My A-5 will not recock. What would be the potential causes of this.
|
|
 |
|
|
>><<
Gold Member 
<<>> Joined: 08 February 2004 Location: Byelorussian SSR Status: Offline Points: 1870 |
Post Options
Thanks(0)
Quote Reply
Posted: 10 November 2005 at 8:46pm |
|
you could have busted a ball in the chamber and got the bolt stuck take apart the gun and see if theres is any paint in the breech and if there is clean and it should work.
|
|
|
|
|
|
|
jjclown23
Gold Member
No idea what’s inappropriate Joined: 05 March 2004 Location: United States Status: Offline Points: 1614 |
Post Options
Thanks(0)
Quote Reply
Posted: 12 November 2005 at 4:02am |
|
have you taken it apart lately? usually the spring that is connected to the thing that you cock it back with can break loose of where it should be.
|
|
|
A-5
Response Trigger DOP Blade Trigger Polished Internals X-Chamber Custom Paint 14" J&J |
|
|
|
|
Tippyprouser
Member
Joined: 09 June 2005 Location: United States Status: Offline Points: 378 |
Post Options
Thanks(0)
Quote Reply
Posted: 12 November 2005 at 2:02pm |
|
Also (stupid thing) make sure you have a full tank....
What they said do that too...take it apart!!!! |
|
|
Setup:
Tippmann Custom Pro E-trigger 12" All American BT Folding Stock GTA Inline Expansion Chamber Kit Dead on Pro seal Cyclone Feed System Remote Line Polished internals |
|
|
|
|
Bruce A. Frank
Platinum Member 
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
Post Options
Thanks(0)
Quote Reply
Posted: 13 November 2005 at 1:35pm |
Loose valve, damaged rear bolt "O" ring, inadequate lubrication. And the obvious one, too little gas in the cylinder. |
|
|
|
|
goats_896
Member
Joined: 24 October 2005 Location: United States Status: Offline Points: 70 |
Post Options
Thanks(0)
Quote Reply
Posted: 13 November 2005 at 8:06pm |
|
Problem fixed. It was my stock bolt. I was just using it for the heck of it, but I put my ST Supafly back in and it's working great! Thanks for the comments.
|
|
|
Zafira
|
|
|
|
|
Tippyprouser
Member
Joined: 09 June 2005 Location: United States Status: Offline Points: 378 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 November 2005 at 10:42pm |
|
I don't understand how that could be...cuz stock internals should always work...but if it worked it worked
|
|
|
Setup:
Tippmann Custom Pro E-trigger 12" All American BT Folding Stock GTA Inline Expansion Chamber Kit Dead on Pro seal Cyclone Feed System Remote Line Polished internals |
|
|
|
|
RedLion56
Member
Joined: 01 September 2005 Location: United Kingdom Status: Offline Points: 475 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2005 at 10:31am |
|
May have been your sear
|
|
|
A5
12"Bigshot Pure energy 20ozCo2x2/AntiSyphon 32 degrees Black X_chamber Pen spring mod Polished Internals |
|
|
|
|
Bruce A. Frank
Platinum Member
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 November 2005 at 12:20pm |
|
But then replacing the front bolt with the Surpa Fly bolt would have made no difference. |
|
|
|
|
Caboose
Member
Joined: 17 November 2005 Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 November 2005 at 6:41pm |
|
Im having the same problem, when i go to cock the gun, it sounds like
the rear bolt is falling back down if i aim the gun at a slight angle,
i took it apart checked everything and it seemed fine so its back
together
|
|
|
|
|
goats_896
Member
Joined: 24 October 2005 Location: United States Status: Offline Points: 70 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 November 2005 at 9:52pm |
|
Did you correct the problem? If not I would have to say that the problem is either with the sear or the rear bolt being worn out too much that it cannot get a good "grip". |
|
|
Zafira
|
|
|
|
|
fathead1616
Member
Joined: 12 October 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 November 2005 at 2:02pm |
|
i think that the sear is not catching the rear bolt.... It has happend to me many times with my Custom Pro
|
|
|
A-5:
egrip with WAS board QEV Dead ON Front grip 14" JJ Ceramic/ flatline JCS Egrip double trigger Richocet Hopper |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
goats_896 wrote: