|
E-Bolt for M98 |
Post Reply 
|
| Author | ||
Bruce A. Frank 
Platinum Member 
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: E-Bolt for M98Posted: 03 January 2006 at 8:09pm |
|
|
Found this: This is a drop in for the M98 but will fit, with minor mod, the 98C. If yo are looking for one, this is the best price I have seen for a while. |
||
 |
||
|
pbdude985
Platinum Member
Dude! Sweet! Dude! Sweet! Dude! Sweet! Joined: 13 July 2004 Location: United States Status: Offline Points: 6876 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 January 2006 at 8:18pm |
|
|
man i want that , that is really cheaop. how much modding do you think it will take?
|
||
|
||
|
||
|
SuzukiRider987
Platinum Member
Joined: 15 October 2004 Location: United States Status: Offline Points: 5643 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 January 2006 at 8:25pm |
|
|
It doesn't take much. You have to mill a little inside the grip frame so the board fits (which is very little), then just make a trigger extension so the trigger will activate the switch (which can be made out of a piece of plastic, etc. |
||
|
||
|
Bruce A. Frank
Platinum Member
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 January 2006 at 8:39pm |
|
This is essentially correct. It doesn't require milling exactly; a Dremel Tool or a hand file will easily do the job. I'd also make another suggestion. The version for the M98 feeds gas to the solenoid via a feed-through-bolt, a replacement for the normal bolt that holds the ASA on to the bottom of the grip. I would notch the front bottom corner of the grip, just as Tippmann did to the 98 C grip, and run the gas tube for the ram in through there. Easier to assemble and disassemble in the future. |
||
|
||
|
SuzukiRider987
Platinum Member
Joined: 15 October 2004 Location: United States Status: Offline Points: 5643 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 January 2006 at 8:51pm |
|
|
While we're on the area of suggestions... I'd also suggest you do the quick strip mod (found here). This will help if you just have to do something in the back or front of the gun, like clean your front bolt, or replace a battery for example. Instead of taking off the whole left reciever, you can just take off half. This is extremelt helpfull if the have the E-Bolt becuase if you need to axcess the front of your gun, you don't have to mess with the electronics in the back.
Edited by SuzukiRider987 |
||
|
||
|
MP Sniper
Member 
Strike 1 Language. 1/22/06 Joined: 06 September 2005 Status: Offline Points: 450 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 January 2006 at 9:32pm |
|
|
yep i just bought the e-bolt, you know its funny i was just about to ask if any body seen any ebolts that are cheaper than 150.00 and here it is man bruce your good man you are really good thanks man
|
||
|
||
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
pbdude985 wrote: