Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

A5 rear pushpin breaks
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Warchilde View Drop Down
Member
Member
Avatar

Joined: 04 October 2005
Status: Offline
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Warchilde Quote  Post ReplyReply Direct Link To This Post Topic: A5 rear pushpin breaks
    Posted: 14 May 2006 at 6:25pm
ANy ideas??

I have a spec ops dog leg stock on my A5, after a day of bushball and about 800 rounds fired I noticed that my  stock was a little loose. I dismantled the gun to clean it and I found that both rear pushpins where broken in half. 

I had a little difficulty putting the push pins in my new stock when I bought it ... I had to use a hammer to tap the push pins in as the wouldnt go in very smoothly but a few gentle taps and they slid right in.

SO what could have caused both push pins to break and how can I avoid this again??  Any ideas?
Back to Top
iceman1186 View Drop Down
Gold Member
Gold Member
Avatar

Joined: 09 October 2002
Location: United States
Status: Offline
Points: 1036 		Post Options Post Options   Thanks (0) Thanks(0)   Quote iceman1186 Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2006 at 9:43pm
Any hard hits to the stock repeatedly will cause the pins to break. The only way to prevent it is to be a little more careful about hitting your hard against things.
Back to Top
Warchilde View Drop Down
Member
Member
Avatar

Joined: 04 October 2005
Status: Offline
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Warchilde Quote  Post ReplyReply Direct Link To This Post Posted: 14 May 2006 at 10:47pm
Thanks but there were no hard hits at all to the stalk. It is confusing ... I am wondering if so how the action of the gun itself is causing the pins to break ... but I am not sure this is possible.
Back to Top
Gropo View Drop Down
Member
Member
Avatar

Joined: 14 May 2006
Status: Offline
Points: 27 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gropo Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2006 at 10:21pm
Hey, read this if haven't already. It speaks to this problem.


http://www.tippmann.com/forum/wwf77a/forum_posts.asp?TID=154 130&PN=1


I don't know if I did the link right. It is under the heading "Ever Seen This?" in this maintenance forum.

It seems others have had this problem with a stock mounted.


Edited by Gropo - 15 May 2006 at 10:25pm
Back to Top
iceman1186 View Drop Down
Gold Member
Gold Member
Avatar

Joined: 09 October 2002
Location: United States
Status: Offline
Points: 1036 		Post Options Post Options   Thanks (0) Thanks(0)   Quote iceman1186 Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2006 at 10:36pm
Originally posted by Gropo Gropo wrote:



Hey, read this if haven't already. It speaks to this problem. http://www.tippmann.com/forum/wwf77a/forum_posts.asp?TID=154 130&PN=1I don't know if I did the link right. It is under the heading "Ever Seen This?" in this maintenance forum.It seems others have had this problem with a stock mounted.


Yea its toward the bottom of the first page.
Back to Top
Ken Majors View Drop Down
Gold Member
Gold Member
Avatar
Tree? What tree? OW!!!! Dangit!!!!

Joined: 02 March 2003
Location: United States
Status: Offline
Points: 2224 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ken Majors Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2006 at 11:10pm
Using a stock on an A-5 causes undue stress on the take-down pins.
Buy a bunch. They are cheap.

They break or bend after a while. The longer, heavier stocks put even more pressure on them.
RLTW
Back to Top
Gropo View Drop Down
Member
Member
Avatar

Joined: 14 May 2006
Status: Offline
Points: 27 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gropo Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2006 at 6:29pm
    That's a bummer. I was thinking of adding the Ben Tippmann folding stock as a future upgrade. I plan to make minimum use of a stock anyway, so a folding stock will be better than a fixed one.

    Does anyone know if the problem is one of leverage stress with a heavy stock? Or is it a problem of alignment caused by using nonstandard parts? Are the stocks not serving as a good end cap?
Back to Top
Snick View Drop Down
Member
Member
Avatar

Joined: 03 October 2005
Location: United States
Status: Offline
Points: 343 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Snick Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2006 at 6:32pm
the thing is that puting on a stock adds extra stress to the pins, I mean think about it, almost the entire weight of the stock rests on those two pushpins. and guess you aren't using the stock, you got the entire weight pushing down on the pins, also, when you ARE using the stock, you have the force of you pushing the stock into the shoulder also pressing against the pins, also don't forget the pressure pushing back against it the other way from the drive spring when the gun is cocked. all in all, using a stock puts alot of stress on the pins...... my sugestion, buy a ton of pushpins, or try and get a stronger set which can deal with the pressure better.

Edited by Snick - 19 May 2006 at 8:26am
Back to Top
VimyRidge View Drop Down
Member
Member
Avatar

Joined: 01 February 2006
Location: Canada
Status: Offline
Points: 120 		Post Options Post Options   Thanks (0) Thanks(0)   Quote VimyRidge Quote  Post ReplyReply Direct Link To This Post Posted: 28 May 2006 at 1:39pm

Hey i've had the same thing happen to me with the OpsGear G36 folding Stock. I determined it was due to the angle it folded at and the pressure exursion.

In the end, I just bought s new stock. nothing can really fix this, but sanding down the stock holes that the pins fit through helps their life. You don't need to hammer them in. If this is the case, enlarge those holes slightly. You'll see this done on a number of reviews with various tippmann stocks.
"The key in war isn't to die for your country, but to make the othe bastard die for his".
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.391 seconds.