R/T help

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I am assuming this is a problem with my Response Trigger, but i dont know.  I put the trigger in my 98 custom and now my gun is having problems firing.  
When i give the gun air i can hear a small leak coming out of the FRONT end the R/T line comes from.  If i shoot the gun a few times the leak goes away(im assuming from the CO2).  When i shoot the gun i get one great shot, then i shoot again and it is weak and the gun does not recock.  
it stays with this patern.
recock gun...great shot...crappy shot no recock
Thank you in advance for everyones help.
Oh...also i have an extra piece from my R/T trigger.   obviously this could be a problem.  The extra piece is the shut off plug...im 90% sure  

Edited by Jfreak7 - 12 June 2006 at 12:16am

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Jfreak7 Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 11 June 2006 Status: Offline Points: 3	Post Options Post Reply Quote Jfreak7 Report Post Thanks(0) Quote Reply Topic: R/T help Posted: 11 June 2006 at 10:35pm
	I am assuming this is a problem with my Response Trigger, but i dont know. I put the trigger in my 98 custom and now my gun is having problems firing. When i give the gun air i can hear a small leak coming out of the FRONT end the R/T line comes from. If i shoot the gun a few times the leak goes away(im assuming from the CO2). When i shoot the gun i get one great shot, then i shoot again and it is weak and the gun does not recock. it stays with this patern. recock gun...great shot...crappy shot no recock Thank you in advance for everyones help. Oh...also i have an extra piece from my R/T trigger. obviously this could be a problem. The extra piece is the shut off plug...im 90% sure Edited by Jfreak7 - 12 June 2006 at 12:16am

FarSeer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 18 April 2006 Location: Montana Status: Offline Points: 649	Post Options Post Reply Quote FarSeer Report Post Thanks(0) Quote Reply Posted: 11 June 2006 at 11:59pm
	Welcome to the forum. Your ball dedent backwards. Happened to me. It took me 20 minutes to figure it out.
	My E-Bolted 98

Jfreak7 Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 11 June 2006 Status: Offline Points: 3	Post Options Post Reply Quote Jfreak7 Report Post Thanks(0) Quote Reply Posted: 12 June 2006 at 12:01am
	Im not sure I understand you. you ball dedent backwards. sorry man. Hey, i have a question for you guys. Can someon just take a picture of there gun and post it? What I am looking for is a picture of the back side of the gun (the side where the R/T trigger line runs). This way I will know if I installed it right. That would help me GREATLY! Oh, obviously, i would need a picture of a 98C with the R/T installed THanx Edited by Jfreak7 - 12 June 2006 at 12:16am

makave7 Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 16 May 2006 Status: Offline Points: 33	Post Options Post Reply Quote makave7 Report Post Thanks(0) Quote Reply Posted: 12 June 2006 at 3:56am
	Hey, first off that shut off plug is not the problem, you only need it to shut off the plug where the power screw for the r/t hose is attached to. Therefore, you dont need it unless you WANT to disarm your r/t. Also, it will be easier if you posted your picture of the gun and people will be able to help you easier. Im guessing its the leak in your power hose that you mentioned. Either make sure you have the hoses on securely and have o rings where it is neccessary, or make sure your screws are on correctly. What the other guy mentions about the ball detent is the little orange rubber thing in front of your front bolt which holds the paintball in place when it drops from your feeder. Make sure it is facing the right way.

paintballinbill Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 06 January 2006 Location: United States Status: Offline Points: 438	Post Options Post Reply Quote paintballinbill Report Post Thanks(0) Quote Reply Posted: 12 June 2006 at 9:59am
	here's a pic of my R/T and cyclone setup. the connector circled in red is the flow control screw. the connector circled in white is the banjo T-fitting, but if you don't have the cyclone, it'll just be a 90* fitting that connects to the power tube.
	98 Custom milled;painted;J&J Ceramic;X-Chamber;R/T;Cyclone.

Jfreak7 Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 11 June 2006 Status: Offline Points: 3	Post Options Post Reply Quote Jfreak7 Report Post Thanks(0) Quote Reply Posted: 13 June 2006 at 6:15pm
	Ok i can see my problem now. The line is backwards. i have the 90 degree fitting at the rear of the gun. Let me try it and see if it works. Also, i think the leak is coming from the air line (from the tank to the gun). I tried fixing it with plumbers tape. didnt work...it actually made it worse ( of course now i know if is definetly coming from there...so it helps a little). Another thing. The black plastic piece that goes in front of the bolt. ( a piece is setting inside it), has a little crack in it. Would this cause air leaks? i am sorry i do not know the lingo for all the parts. I will try and get pictures. they should help me and you

cus98tom Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 12 July 2005 Status: Offline Points: 491	Post Options Post Reply Quote cus98tom Report Post Thanks(0) Quote Reply Posted: 13 June 2006 at 9:45pm
	This is in reference to your last post : What you are describing sounds like the power tube, if it has a crack in it it needs to be replaced.