Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

Mask Problem
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
jedi mike0 View Drop Down
Member
Member
Avatar

Joined: 06 December 2006
Location: Canada
Status: Offline
Points: 33 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jedi mike0 Quote  Post ReplyReply Direct Link To This Post Topic: Mask Problem
    Posted: 17 May 2007 at 5:10pm
I know this is in the gun tech section, but this is kind of a technical thing.  I have a JT Spectra Flex 8 Full coverage paintball mask, and I'm having a bit of trouble taking the lens off.  And yes, I have read all the instructions and everything.  My problem is I can't seem to take the lens out of the nose part.  I've been able to take it from the top, sides, but now I can't get it from the nose part.  There was a picture in the instruction manual where it showed someone squeezing the nose part to get the mask out, but that doesn't seem to work for me.  Sorry if this doesn't make sense.  If you need me to clarify on anything just ask and I'll do my best.  Thanks in advance!
Back to Top
Bruce A. Frank View Drop Down
Platinum Member
Platinum Member
Avatar
KRL Reincarnated?

Joined: 27 March 2004
Location: United States
Status: Offline
Points: 3063 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bruce A. Frank Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2007 at 9:51pm

Originally posted by jedi mike0 jedi mike0 wrote:

I know this is in the gun tech section, but this is kind of a technical thing.  I have a JT Spectra Flex 8 Full coverage paintball mask, and I'm having a bit of trouble taking the lens off.  And yes, I have read all the instructions and everything.  My problem is I can't seem to take the lens out of the nose part.  I've been able to take it from the top, sides, but now I can't get it from the nose part.  There was a picture in the instruction manual where it showed someone squeezing the nose part to get the mask out, but that doesn't seem to work for me.  Sorry if this doesn't make sense.  If you need me to clarify on anything just ask and I'll do my best.  Thanks in advance!

The lens has two barb like points that point upward. You have to squeeze the rubbery nose area of the mask to disengage the barbs. It may help to gently rock the lens side to side. Usually this will pop one barb loose and the other side then come out easily. Be careful, if you break a point the lens will not stay in place properly, a dangerous situation, and will have to be replaced.
Back to Top
jedi mike0 View Drop Down
Member
Member
Avatar

Joined: 06 December 2006
Location: Canada
Status: Offline
Points: 33 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jedi mike0 Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2007 at 4:43pm
Thanks a lot for the help!  I've managed to get it out, clean it, and put it back in again.


Edited by jedi mike0 - 18 May 2007 at 8:07pm
Back to Top
Bruce A. Frank View Drop Down
Platinum Member
Platinum Member
Avatar
KRL Reincarnated?

Joined: 27 March 2004
Location: United States
Status: Offline
Points: 3063 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bruce A. Frank Quote  Post ReplyReply Direct Link To This Post Posted: 18 May 2007 at 9:06pm

Originally posted by jedi mike0 jedi mike0 wrote:

Thanks a lot for the help!  I've managed to get it out, clean it, and put it back in again.

And if you are like I am you then probably had to clean it all over again due to the finger print smears.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.297 seconds.