| Author |
 Topic Search  Topic Options
|
Ilford Rule 
Gold Member
Joined: 05 December 2005
Location: Canada
Status: Offline
Points: 1460
|
 Topic: PLEASE HELP! (chop/skip)
Posted: 02 January 2006 at 9:32pm |
|
Ok, im not sure what the problem is. I was hoping some people here can
help me.
I am chopping like crazy. I am shooting the stock mechanical trigger on
the CPro. Last time I played, i didn't chop a single ball. However i
was told that it was possible to outshoot a gravity feed hopper with a
mechanical trigger, so i tried to do so. Lo and behold i did. So i went
and bought an empire reloader 2 agitating hopper. Today i started
chopping like crazy. Also, when i shoot without the barrel (14"
teardrop) on and without paint, i get "snow" (frozen Co2) coming out
from the bolt port (im not using rocket cock, i have the open port on
the side of the gun). all the O-rings that i can see without taking
apart the valve/power tube on the inside of the gun after basic
disassembly are fine. Also, the gun is skipping every now and then (i
shoot, the bolt goes forward, and then doesn't make it back all the way
and is fired forward again, catching the sear the second time). I
checked the sear and it's fine. No obstructions in the bolt area.
PLEASE HELP!
|
CPro (w/ polished internals)
14" Bigshot
BT SBS
Various Rails
NcSTAR D4B
Macro
AA 68/45
CCI Phantom
45 Grips
|
 |
>><<
Gold Member
<<>>
Joined: 08 February 2004
Location: Byelorussian SSR
Status: Offline
Points: 1870
|
Posted: 02 January 2006 at 9:35pm |
|
Lets see make sure your bolt is clean no paint left in there check and see if theres any obstructions in the elbow and for the c02 part it was probably cold so the gas stayed as a liquid so it would be the best for your gun to change to HPA.
|
|
|
|
Ilford Rule
Gold Member
Joined: 05 December 2005
Location: Canada
Status: Offline
Points: 1460
|
Posted: 02 January 2006 at 9:36pm |
|
Hmmm... i considered this. But i had two friends playing today with A5's on Co2 and they worked fine.
|
CPro (w/ polished internals)
14" Bigshot
BT SBS
Various Rails
NcSTAR D4B
Macro
AA 68/45
CCI Phantom
45 Grips
|
|
Ilford Rule
Gold Member
Joined: 05 December 2005
Location: Canada
Status: Offline
Points: 1460
|
Posted: 02 January 2006 at 9:39pm |
|
wait why would liquid co2 cause me to chop and skip? could it be a problem with the power tube?
|
CPro (w/ polished internals)
14" Bigshot
BT SBS
Various Rails
NcSTAR D4B
Macro
AA 68/45
CCI Phantom
45 Grips
|
|
You Wont See Me
Moderator Group
Found in Big Al’s underwear drawer
Joined: 02 December 2003
Location: Neutral Zone
Status: Offline
Points: 13335
|
Posted: 02 January 2006 at 9:39pm |
 You Wont See Me wrote:
Also in upgrades and customizing....
The liquid c02 is because its cold out
The chopping is because of bad paint, and/or your outshooting your hopper.
|
|
|
A-5
E-Grip
JCS Dual Trigger
DOP X-CORE 8 stage x-chamber
Lapco Bigshot 14" Beadblasted
Optional setup:
R/T
Dead on Blade trigger
|
|
Ilford Rule
Gold Member
Joined: 05 December 2005
Location: Canada
Status: Offline
Points: 1460
|
Posted: 02 January 2006 at 9:43pm |
You Wont See Me wrote:
You Wont See Me wrote:
Also in upgrades and customizing....
The liquid c02 is because its cold out
The chopping is because of bad paint, and/or your outshooting your hopper.
|
|
Wait its skipping because of cold Co2?
Also, i wasn't outshooting my hopper (only shooting 5-8 bps on a 12-14
bps hopper.i think the detent might have been in backwards though,
fixed now. Would a tank cover help the cold co2 problem or is HPA the
only solution?
What do i need in order to switch to HPA? do i just need the tank or is there something else?
Edited by Ilford Rule
|
CPro (w/ polished internals)
14" Bigshot
BT SBS
Various Rails
NcSTAR D4B
Macro
AA 68/45
CCI Phantom
45 Grips
|
|
Rambino
Platinum Member
I am even less fun in person
Joined: 15 August 2002
Location: United States
Status: Offline
Points: 16593
|
Posted: 02 January 2006 at 10:22pm |
|
Enough with the multi-forum spamming already.
|
|
[IMG]http://i38.tinypic.com/aag8s8.jpg">
|
|
Tweet
PLEASE HELP! (chop/skip)