|
Vortex Mod..spring ? |
Post Reply 
|
| Author | |
Mr. Blonde 
Member 
Guested - Rudeness Joined: 29 September 2006 Status: Offline Points: 418 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Vortex Mod..spring ?Posted: 04 October 2006 at 6:57pm |
|
Ok, I finished installing my Vortex and used Shocker Lube, however I had problems cutting the spring.. it said one turn, I did atleast three or four, however I tested it (manually like it said) and it turns and cycle right....why does it say not to cut the spring more than one turn?
|
|
|
-Tippmann A-5
-Flatline + Metadyne Shroud -R.I.S. Foregrip -X-Core -JCS Aluminum Powertube -JCS Hexagon Bolt -Q.E.V. -Vortex -E-Grip -Shocktech Drop\On\Off ASA -Macro-Line -Anti-Siphon C02 |
|
 |
|
|
paintballinbill
Member
Joined: 06 January 2006 Location: United States Status: Offline Points: 438 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 October 2006 at 7:09pm |
|
first things first:
unless you were involved in the planning/design of this product, or have an extensive knowledge of it, why did you disobey the installation instructions? you may have gotten lucky, but why wouldn't you just do what the instructions say? |
|
|
98 Custom
milled;painted;J&J Ceramic;X-Chamber;R/T;Cyclone. |
|
|
|
|
Mr. Blonde
Member
Guested - Rudeness Joined: 29 September 2006 Status: Offline Points: 418 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 October 2006 at 7:25pm |
|
Uh, good to see you again Bill I"m >>>PAUL<<< on your Myspace. Anyway, basically I had VERY bad wire-cutters, and when I pressed it it wouldn't cut, so I had to take it off, when I did, it unravled more the spring, so I just cut it after that because I had enough "room" to get the shrap part of the wire-cutter in (very back of it) Long Story Short - I didn't mean to, I accidently messed up and couldn't go back.
Edited by Mr. Blonde - 04 October 2006 at 7:26pm |
|
|
-Tippmann A-5
-Flatline + Metadyne Shroud -R.I.S. Foregrip -X-Core -JCS Aluminum Powertube -JCS Hexagon Bolt -Q.E.V. -Vortex -E-Grip -Shocktech Drop\On\Off ASA -Macro-Line -Anti-Siphon C02 |
|
|
|
|
paintballinbill
Member
Joined: 06 January 2006 Location: United States Status: Offline Points: 438 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 October 2006 at 5:42pm |
|
oh ok. sorry to go all crazy on you there, it sounded like you wanted to cut off more coils just for the hell of it.... and what's this about myspace? i'm confused.....do i know you? |
|
|
98 Custom
milled;painted;J&J Ceramic;X-Chamber;R/T;Cyclone. |
|
|
|
|
Mr. Blonde
Member
Guested - Rudeness Joined: 29 September 2006 Status: Offline Points: 418 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 October 2006 at 11:44pm |
|
Yes... I'm on your myspace, you added me ALONG time ago...oh wait nevermind.. the dude that added me that was from this forum.. his name is paintballin_psycho, that's why I got you two confused.. lol sorry.
|
|
|
-Tippmann A-5
-Flatline + Metadyne Shroud -R.I.S. Foregrip -X-Core -JCS Aluminum Powertube -JCS Hexagon Bolt -Q.E.V. -Vortex -E-Grip -Shocktech Drop\On\Off ASA -Macro-Line -Anti-Siphon C02 |
|
|
|
|
StormyKnight
Moderator Group 
Joined: 28 July 2003 Location: United States Status: Offline Points: 3129 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 October 2006 at 7:56am |
|
I haven't cut the drive spring on mine yet. Holding out on how the marker performs with the stock spring length before I modify it.
|
|
|
|
|
|
|
Mr. Blonde
Member
Guested - Rudeness Joined: 29 September 2006 Status: Offline Points: 418 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 October 2006 at 3:23pm |
|
It woulda been alot nicer if they included a pre-cut drive spring
|
|
|
-Tippmann A-5
-Flatline + Metadyne Shroud -R.I.S. Foregrip -X-Core -JCS Aluminum Powertube -JCS Hexagon Bolt -Q.E.V. -Vortex -E-Grip -Shocktech Drop\On\Off ASA -Macro-Line -Anti-Siphon C02 |
|
|
|
|
cus98tom
Member
Joined: 12 July 2005 Status: Offline Points: 491 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 October 2006 at 9:18pm |
|
They want a certain amont of pressure on the feeder axle, if there is not enough (pressure) the feeder axle will have to much slop in the movement , you will see the sproket move back and forth more than normal. you may or may not have problems. |
|
|
|
|
Mr. Blonde
Member
Guested - Rudeness Joined: 29 September 2006 Status: Offline Points: 418 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 October 2006 at 11:21pm |
|
I tested it today....only a couple skips, and I think that's cause I didn't have my QEV on and was useing TURBO mode at 15bps. No chops though.
|
|
|
-Tippmann A-5
-Flatline + Metadyne Shroud -R.I.S. Foregrip -X-Core -JCS Aluminum Powertube -JCS Hexagon Bolt -Q.E.V. -Vortex -E-Grip -Shocktech Drop\On\Off ASA -Macro-Line -Anti-Siphon C02 |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
Mr. Blonde wrote:
my bad.