pro lite and pro carbine problems

Author

Message

Topic Search

Topic Options

wickedclownz View Drop Down

Member

Joined: 13 January 2005
Location: United States
Status: Offline
Points: 1

Post Options

Post Reply

Quote wickedclownz

Report Post

Thanks(0)

Quote

Topic: pro lite and pro carbine problems
Posted: 10 April 2005 at 11:09am

hey guys and gals i was wondering on my pro lite you have to do full trigger pull on it which is you can push it back but you also have to push it forward and on the pro carbine the bolt will not reset it self the tank is full and ive tried everything with the velocity you can fire it once and the bolt will not shoot it self backwards thanks for anything that could be of help

Dont watch for me ill find you first

txsniper

Member

Joined: 16 March 2005
Location: United States
Status: Offline
Points: 3

Post Options

Post Reply

Quote txsniper

Report Post

Thanks(0)

Quote

Posted: 23 April 2005 at 6:38am

check the trigger spring first then it sound like it could use a real good cleaning. If the bolt is not being pushed back it sounds like an air problem, there might be a restriction somewhere. Hard to tell without seeing it though

clownshooter View Drop Down

Moderator Group

Checking your underwear drawer

Joined: 15 June 2002
Location: United States
Status: Offline
Points: 3371

Post Options

Post Reply

Quote clownshooter

Report Post

Thanks(0)

Quote

Posted: 23 April 2005 at 9:03pm

1. Check to see if the linkage rod is hooked to the front bolt.
2. Check front and rear bolt o-rings and inside of receiver for old crud.
3. It may be valve related, but I doubt it since it does at least shoot out the paintball on the first shot. It really sounds like a linkage rod problem.
The Pro-Lite, may have a bad or stretched out trigger spring.

SR_Crewchief View Drop Down

Platinum Member

Joined: 12 June 2002
Location: United States
Status: Offline
Points: 2663

Post Options

Post Reply

Quote SR_Crewchief

Report Post

Thanks(0)

Quote

Posted: 23 April 2005 at 10:00pm

First the obvious question. When was the last time it was full stripped for cleaning?

Now for the not so obvious.

For the trigger, has it been shimmed to reduce axial play? If so, it may need to be reduced.

A new spring is never a bad idea.

For the hammer issue. Clownshooter covered the linkage arm.

Also check the drive pin for straightness. You could also have a weak driver spring.

When was the last time the valve was lubed?

If the o-ring for the valve to body seal is worn you could the this problem as well.

Honestly, before doing anything else, down a full stripdown, clean/lube, and reassemble. Don't forget to do the internal lube for the valve while your at it. Replace any o-ring with obvious damage.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
wickedclownz Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 13 January 2005 Location: United States Status: Offline Points: 1	Post Options Post Reply Quote wickedclownz Report Post Thanks(0) Quote Reply Topic: pro lite and pro carbine problems Posted: 10 April 2005 at 11:09am
	hey guys and gals i was wondering on my pro lite you have to do full trigger pull on it which is you can push it back but you also have to push it forward and on the pro carbine the bolt will not reset it self the tank is full and ive tried everything with the velocity you can fire it once and the bolt will not shoot it self backwards thanks for anything that could be of help
	Dont watch for me ill find you first

txsniper Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 16 March 2005 Location: United States Status: Offline Points: 3	Post Options Post Reply Quote txsniper Report Post Thanks(0) Quote Reply Posted: 23 April 2005 at 6:38am
	check the trigger spring first then it sound like it could use a real good cleaning. If the bolt is not being pushed back it sounds like an air problem, there might be a restriction somewhere. Hard to tell without seeing it though

clownshooter Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Checking your underwear drawer Joined: 15 June 2002 Location: United States Status: Offline Points: 3371	Post Options Post Reply Quote clownshooter Report Post Thanks(0) Quote Reply Posted: 23 April 2005 at 9:03pm
	1. Check to see if the linkage rod is hooked to the front bolt. 2. Check front and rear bolt o-rings and inside of receiver for old crud. 3. It may be valve related, but I doubt it since it does at least shoot out the paintball on the first shot. It really sounds like a linkage rod problem. The Pro-Lite, may have a bad or stretched out trigger spring.

SR_Crewchief Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Joined: 12 June 2002 Location: United States Status: Offline Points: 2663	Post Options Post Reply Quote SR_Crewchief Report Post Thanks(0) Quote Reply Posted: 23 April 2005 at 10:00pm
	First the obvious question. When was the last time it was full stripped for cleaning? Now for the not so obvious. For the trigger, has it been shimmed to reduce axial play? If so, it may need to be reduced. A new spring is never a bad idea. For the hammer issue. Clownshooter covered the linkage arm. Also check the drive pin for straightness. You could also have a weak driver spring. When was the last time the valve was lubed? If the o-ring for the valve to body seal is worn you could the this problem as well. Honestly, before doing anything else, down a full stripdown, clean/lube, and reassemble. Don't forget to do the internal lube for the valve while your at it. Replace any o-ring with obvious damage.