Tippmann Paintball Homepage
Forum Home Forum Home > Tippmann Paintball > Paintball Ideas / News From Tippmann
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

Metal end Caps
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
D-BEAT View Drop Down
Member
Member


Joined: 23 December 2006
Location: United States
Status: Offline
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote D-BEAT Quote  Post ReplyReply Direct Link To This Post Topic: Metal end Caps
    Posted: 28 December 2006 at 1:27pm

As of yesterday i had my 98 custom's act spring just plow right through the end cap and shoot out of the rear. I called tippmann and they are sending me a new one , along with a plastic act pin (???) or somthing. They said that they had to many of this same problem so they were turnging to plastic. My question is why not make metal end caps? this is the only other plastic peice on the marker besides the fore grip, and it sure takes a lot of internal abuse.

Does any one else have this same problem and think metal end caps are a good idea?
98% of paintballers act gangsta', if you are the 2% that are normal, put this in your sig.
Back to Top
ShortyBP View Drop Down
Moderator Group
Moderator Group

A G F Y

Joined: 10 June 2002
Location: United States
Status: Offline
Points: 5034 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ShortyBP Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 1:50pm
I cannot recall the specifics, but metal end caps were originally conceived and were ultimately trashed in favor of the plastic. I believe they were prone to failure as well... but do not recall exactly what.
Either the end caps were cracking, or the receiver halves were. Either way, the plastic ones held up to repeated cycling better.

Edited by ShortyBP - 28 December 2006 at 1:51pm
Back to Top
DeTrevni View Drop Down
Moderator Group
Moderator Group
Avatar
b-YOU-ick. Was that so hard?

Joined: 19 September 2005
Location: Houston, Texas
Status: Offline
Points: 11957 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DeTrevni Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 2:59pm
Well, the metal would just hold up to the energy of the kick. The plastic theoretically absorbs it. I'd think the plastic caps were better. I've never personally had one shoot out the back before...
Evil Elvis: "Detrevni is definally like a hillbilly hippy from hell"
Back to Top
D-BEAT View Drop Down
Member
Member


Joined: 23 December 2006
Location: United States
Status: Offline
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote D-BEAT Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 3:33pm
How about they make a hybrid one, with plastic casing around a metal plate in the back. Although it would cost alot more....
98% of paintballers act gangsta', if you are the 2% that are normal, put this in your sig.
Back to Top
pattison View Drop Down
Member
Member
Avatar

Joined: 30 August 2002
Location: Korea, North
Status: Offline
Points: 384 		Post Options Post Options   Thanks (0) Thanks(0)   Quote pattison Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 4:44pm
lapco rva
Eat The Brisket
Back to Top
The Guy View Drop Down
Platinum Member
Platinum Member
Avatar
Soup Can Guy

Joined: 18 March 2004
Status: Offline
Points: 6666 		Post Options Post Options   Thanks (0) Thanks(0)   Quote The Guy Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 5:49pm
in the end plastic was just cheaper
My Site
Back to Top
Mack View Drop Down
Moderator Group
Moderator Group
Avatar
Has no impulse! control

Joined: 13 January 2004
Location: 2nd Circle
Status: Offline
Points: 9906 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mack Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 6:34pm
Normally, the end caps don't fail as long as the buffer O-ring is in place and in good condition. The problem with metal end caps (or rva's) is that they transfer the stress to the body. I have seen the results of failing to put the buffer O-ring back during reassembly under both sets of circumstances:
  • With the stock end cap, the plastic ring that holds it in place broke off allowing the internals to depart through the rear end of the marker.
  • With a metal rva in place, the rings molded into the (pot metal) marker body failed. The results were the same with the exception that the individual had to get a new body.
Back to Top
barn_user View Drop Down
Gold Member
Gold Member
Avatar
Strike 1 - Filterdodge, 3/20

Joined: 28 May 2006
Location: United States
Status: Offline
Points: 1423 		Post Options Post Options   Thanks (0) Thanks(0)   Quote barn_user Quote  Post ReplyReply Direct Link To This Post Posted: 28 December 2006 at 11:22pm
Imagine playing while aiming your gun at somebody and firing if that would happen...
Back to Top
D-BEAT View Drop Down
Member
Member


Joined: 23 December 2006
Location: United States
Status: Offline
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote D-BEAT Quote  Post ReplyReply Direct Link To This Post Posted: 29 December 2006 at 12:37am
Thats pretty much what happend to me. It was scary as heck! Normaly i only expect projectiles to come from one end of the barrell, but yesterday i was proven wrong......
98% of paintballers act gangsta', if you are the 2% that are normal, put this in your sig.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.672 seconds.