TCR air leaks and other ailments

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   hi guys any input would be welcomed
so I've owned my tcr for about 1 month now. just recently though, the markers been making squelching noises when shot and when i go to adjust the velocity on the dial, air rushes out of the remote line adapter, this is all on air by the way. so when i opened the marker up i found that the o-ring from the rear of the breach block, was tangled up in the mainspring. i placed the ring back were it should go and the marker still made the noise and leaked, when i opened it again the ring had became tangled once more. 
any help is greatly appreciated 
thanks guys 

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Nzballer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 15 April 2016 Location: New Zealand Status: Offline Points: 2	Post Options Post Reply Quote Nzballer Report Post Thanks(0) Quote Reply Topic: TCR air leaks and other ailments Posted: 01 May 2016 at 4:57am
	hi guys any input would be welcomed so I've owned my tcr for about 1 month now. just recently though, the markers been making squelching noises when shot and when i go to adjust the velocity on the dial, air rushes out of the remote line adapter, this is all on air by the way. so when i opened the marker up i found that the o-ring from the rear of the breach block, was tangled up in the mainspring. i placed the ring back were it should go and the marker still made the noise and leaked, when i opened it again the ring had became tangled once more. any help is greatly appreciated thanks guys

spydercam Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Like a mad scientist, but with Tippmanns Joined: 31 January 2008 Location: Germany Status: Offline Points: 1000066	Post Options Post Reply Quote spydercam Report Post Thanks(0) Quote Reply Posted: 01 May 2016 at 6:51am
	Hi, so if your TCR is pretty new i think you don´t want to sand the ares inside a bit where the bolt moves !?!? May if you screwed the screws to tight looose them a bit it will help against the Sound that was on my TPX(same Valvesystem) too. I´ve sanded my cause if you screw i together to softly screws can get lose or lost onfield !!! Does the air rushes through the remote or just in that area ??? I´m pretty shure it´s the pressure relief valve, the screw for is in the same Position like the one you use for adjust the velocity but it´s a smaller wrench. If your marker has home temperature turn it max. right(just to the end Position, no strong force needed), than adjust the velocity and finally turn the screw left slowly till it leaks and than turn it back 1/4 turn(that´s for safty, if the internal pressure gets to high it´will leak). I use grease to glue that O-Ring at the breach for Assembling cause if it´s not in right Position things happen like it happend to you !!! So now it´s your turn again !!!
	I like Tippmann !!!

Nzballer Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 15 April 2016 Location: New Zealand Status: Offline Points: 2	Post Options Post Reply Quote Nzballer Report Post Thanks(0) Quote Reply Posted: 02 May 2016 at 1:57am
	thanks man so iv'e pulled apart all the insides cleaned them, I've reset the adjuster screw in the velocity valve. but now the air leaks around the trigger area

spydercam Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Like a mad scientist, but with Tippmanns Joined: 31 January 2008 Location: Germany Status: Offline Points: 1000066	Post Options Post Reply Quote spydercam Report Post Thanks(0) Quote Reply Posted: 02 May 2016 at 6:19am
	Mmhhh Trigger area ... could be everywhere inside !!! I think may it´s an O-Ring at the gasline(Very small get easy damaged use enough oil to fit them in with low force). If you had this dissconnected !!! The Punturevalve should be OK i´ve never seen Trouble with it, may if the co2 cartriges are shorter than they should so it can´t seal !?!?! When i dissasemble my one i take out (valve with bolt, Regulator, gasline and punturevalve) all in one Piece so i don´t have to fit in the O-rings each time ! I let the Barrel installed so i can fix the breach when opening the Shell and also push the safety button to have less trouble. I know it´s not a plessure to do this but your getting better each time(i did that may 100times in the last month´s cause building the E-TPX) Edited by spydercam - 02 May 2016 at 6:38am
	I like Tippmann !!!