tippmann sl-68 ii gen 2 problem |
Post Reply |
Author | |
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
Posted: 13 January 2013 at 5:15pm |
I bought this sl-68 ii off fo craigslist for 50 bucks and went out and used it and had a blast. the thing worked flauless. But after i took it apart to clean it for the first time and didnt really no what i was doing and something must be missing because when i went to use it again the gun wont work. i figured out that the hammer is being pushed back to far so the trigger cant ingage it. I cant figure out if im missing a piece of **edited** is going on. any help would be greatly appreciated.
|
|
tallen702
Moderator Group Hipster before Hipster was cool... Joined: 10 June 2002 Location: Under Your Bed Status: Offline Points: 11851 |
Post Options
Thanks(0)
|
Tippmannparts.com has schematics available which will let you see what part you may be missing. I suggest you check it out. Paintball markers, while rugged, can be tricky if you don't know what you're doing when performing maintenance or upgrades. Always have a schematic handy so you can see what should be in the marker, and how the parts should fit in until you become very familiar with it. |
|
<Removed overly wide sig. Tsk, you know better.>
|
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
i was using a schimatic to put it back together and when looking at the schematic it doesnt seem like im missing any pieces. Any ideas?
|
|
SSOK
Moderator Group The Savior of Christmas Joined: 01 September 2005 Location: PRNJ Status: Offline Points: 5919 |
Post Options
Thanks(0)
|
How much did you disassemble it? If you just did a field strip there isn't anything to really mess up. Let us know
|
|
|
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
all i did was field strip it. i pulled out the barrel and bolt assembly. then after i cleaned and oiled it i put it back in the same way it came out. but every time i pump the gun the rear bolt and sear seem to be pushed back to far so that the trigger cant engage it. the valve tube is being pushed through the hole in the rear bolt, thats where i thought i was missing a washer. Do you get what i mean?
|
|
Mack
Moderator Group Has no impulse! control Joined: 13 January 2004 Location: 2nd Circle Status: Offline Points: 9906 |
Post Options
Thanks(0)
|
Are you testing it while it is aired up? The bolt and hammer won't engage unless there is pressure in the marker.
|
|
|
|
BearClaw
Moderator Group Joined: 19 August 2003 Location: Canada Status: Offline Points: 2102 |
Post Options
Thanks(0)
|
If its aired up and it's still not cocking make sure ya did not turn in the pump rod too much or lossen it off too much (usually causes a leak).
|
|
AGD 68 Automag
Azodin KPII Sheridan PGP2K Tippmann Crossover XVR Tippmann ProCarbine Tippmann SL68-II Tippmann TiPX |
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
i did test it while it was aired up and still had the same problem. i pumped it and it shot once and then pumped it again and nothing. Have you guys seen any videos that show dissasembling and reassembling it?
thanks again!! |
|
BearClaw
Moderator Group Joined: 19 August 2003 Location: Canada Status: Offline Points: 2102 |
Post Options
Thanks(0)
|
Did you accidentally adjust the pump rod length then. It very easy to do as one you have pump arm off the rod spins easily witch in turn lengthens or shortens your pump stroke.
|
|
AGD 68 Automag
Azodin KPII Sheridan PGP2K Tippmann Crossover XVR Tippmann ProCarbine Tippmann SL68-II Tippmann TiPX |
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
i did ajust it but iv tried every different ajustment it can do. when you cock the gun with out air attached does yours still relase the bolt when fired?
|
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
|
|
notyodady
Member Joined: 13 January 2013 Status: Offline Points: 7 |
Post Options
Thanks(0)
|
im a retard guys. you were right about the pump arm. I was using a empty co2 tank which i was told was full and once i did both of them. it works like a charm! thank you guys so much!!!
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |