Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

Tippmann 98 won't stop firing when fired
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Smafugula View Drop Down
Member
Member


Joined: 16 February 2013
Status: Offline
Points: 1 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Smafugula Quote  Post ReplyReply Direct Link To This Post Topic: Tippmann 98 won't stop firing when fired
    Posted: 16 February 2013 at 10:21pm
Hello all,
 
My tippmann 98 custom will not stop firing when i shoot it. It doesn't shoot anything except the first shot, it just goes auto and I have to take the CO2 out (quickly) to end the madness. Does anyone know whats wrong with it? One of the O rings had broken which was the start of the problem, so I replaced it with a tippmann o ring but still the problem persists. Anyone have any ideas? I did silicone it with airsoft silicone but maybe not enough? Any insight on this problem is greatly appreciated.
Back to Top
God View Drop Down
Moderator Group
Moderator Group

Pull My Finger

Joined: 09 May 2004
Status: Offline
Points: 1381 		Post Options Post Options   Thanks (0) Thanks(0)   Quote God Quote  Post ReplyReply Direct Link To This Post Posted: 16 February 2013 at 10:57pm
Sounds like your tank is low on air.
Back to Top
Mack View Drop Down
Moderator Group
Moderator Group
Avatar
Has no impulse! control

Joined: 13 January 2004
Location: 2nd Circle
Status: Offline
Points: 9906 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mack Quote  Post ReplyReply Direct Link To This Post Posted: 17 February 2013 at 12:18pm
While my first instinct is to agree with God, your post leaves some questions unanswered.

Originally posted by Smafugula Smafugula wrote:

Hello all,
 
My tippmann 98 custom will not stop firing when i shoot it. It doesn't shoot anything except the first shot, it just goes auto and I have to take the CO2 out (quickly) to end the madness.

You can also end the madness by grabbing the charging handle and holding it to the rear.

Does anyone know whats wrong with it? One of the O rings had broken which was the start of the problem, so I replaced it with a tippmann o ring but still the problem persists.

Which o-ring was broken and what do you mean by a "Tippmann o-ring?"

Anyone have any ideas? I did silicone it with airsoft silicone but maybe not enough?

Exactly what did you put airsoft silicone on?  This shouldn't be necessary at all.

Any insight on this problem is greatly appreciated.
Back to Top
Dagfinn Vikse View Drop Down
Member
Member
Avatar

Joined: 03 March 2013
Location: Norway
Status: Offline
Points: 1 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dagfinn Vikse Quote  Post ReplyReply Direct Link To This Post Posted: 03 March 2013 at 5:20pm
hi you probaly have the same problem as you have. you have to clean part Blue and part green. Part red is the pin. if the hole the pin goes to is geting larger  you may have to change the body reciever or you can glue the pin, so it stay stick.  Please let me now if this fix your issue:)

Best regards Dagfinn Vikse
www.viksepaintball.no   NORWAY
Back to Top
Parts Tech View Drop Down
Member
Member


Joined: 08 March 2009
Status: Offline
Points: 59 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Parts Tech Quote  Post ReplyReply Direct Link To This Post Posted: 03 March 2013 at 7:00pm
It is important to note that this rapid-misfire will damage the sear if it happens a lot.  When the sear does not catch to stop the bolt, it gets hammered.  This slowly rounds the edge of the sear.  
Tech at TippmannParts.com
We do everything Tippmann
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.735 seconds.