*EDIT: need a part 4 my impulse* |
Post Reply |
Author | |
FiLiPiNo_RiPpA
Member Joined: 19 February 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
Posted: 15 March 2005 at 3:11pm |
alright I have an impulse and well my friend wuzz dumb and try screwing a co2 tank in there and near the lpr it made some sound like crrrrrrrrrrrrrrrrrrrrr.......... and stuff so i unscrewed do i just need my imp fixed or iz it cuzz co2 is too high pressured and my imp gauge says 300 so its low pressure???? well any help would be appreciated
and heres a pic of my impulse EDIT:::::::::::::::::::::::::::::::::::::::::::::::::::::: yeh the part is a valve seat locator, I found sites that sell teh valve but do they need a valve seat locator to work cuzz i havent found on on them Edited by FiLiPiNo_RiPpA |
|
If the end is the start then where does it end.....
|
|
triggerhappy1
Platinum Member Joined: 07 May 2004 Location: United States Status: Offline Points: 3376 |
Post Options
Thanks(0)
|
Co2 is fine for Impulses. The full 800psi+ is regulated down to 300psi by the regulator. Impulses run good on Co2.
|
|
|
|
FiLiPiNo_RiPpA
Member Joined: 19 February 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
|
so then wats wrong with my impulse lol it makes a leak sound weneva i put a co2 tank in it???
|
|
If the end is the start then where does it end.....
|
|
triggerhappy1
Platinum Member Joined: 07 May 2004 Location: United States Status: Offline Points: 3376 |
Post Options
Thanks(0)
|
Where do you say the sound is coming from? It sounds like a leak or bad o-ring. It could be from the fittings, or macro. So find the leak using some soapy water, and reseal whats leaking with some teflon tape or whatever is appropriate. |
|
|
|
FiLiPiNo_RiPpA
Member Joined: 19 February 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
|
ok i stopped the link on the lpr with sum tanks 2 some teflon but now i hear it in the ram is any help???
|
|
If the end is the start then where does it end.....
|
|
Impulsive
Member Joined: 16 March 2005 Status: Offline Points: 86 |
Post Options
Thanks(0)
|
Put an antisiphon on the tank along with an on/off immediately.
300PSI? Man, make the dwell time longer and lower the pressure. |
|
Cockers are like stick shifts, after a few transmissions you get the hang of them.
|
|
FiLiPiNo_RiPpA
Member Joined: 19 February 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
|
yeh i just found that out but big question i just realized that my impulse is missing the valve the guy who sold it 2 me didnt have one inside the end cap i see a few sites that sell new valves for the impulse but do they need that part called the valve seat locator 2 work bcuzz they dotn show one with them
|
|
If the end is the start then where does it end.....
|
|
xXxMidgeTxXx
Member Joined: 05 March 2004 Location: United States Status: Offline Points: 286 |
Post Options
Thanks(0)
|
|
|
FiLiPiNo_RiPpA
Member Joined: 19 February 2005 Location: United States Status: Offline Points: 18 |
Post Options
Thanks(0)
|
yeh thanks but wats that part inside the impulse that holds the valve in its like a screw and i dont noe where i can order one??? its called a valve seat locator i tink???
|
|
If the end is the start then where does it end.....
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |