Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

**Uncocking**
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
FireStrorm89 View Drop Down
Member
Member
Avatar

Joined: 28 March 2005
Location: United States
Status: Offline
Points: 40 		Post Options Post Options   Thanks (0) Thanks(0)   Quote FireStrorm89 Quote  Post ReplyReply Direct Link To This Post Topic: **Uncocking**
    Posted: 03 July 2005 at 1:34am

   This is the most annoying little problem I get when I play on fields. For some reason everytime I show it to my local paintball dealer, it works flawlessly like nothing ever was wrong.  I shoot once and its fine... than when I shoot again, the paint ball just flops out of the barrel like a dead fish and the cock does not reset and remains in the (UNCOCKED) position. Than when you have to manually reset the thing (like a sniper rifle) it shoots like a monster as though the velocity knob was maxed and the gun shoots over 400 feet per second! And of course after this, you shoot again and it is (Uncocked again)     This is the most annoying problem of all. I tried adjusting the velocity screw (didn't work) I tried oiling the rear bolt (didn't work either) and I tried replacing the tank O-ring (still didn't work) 

    What the hell is wrong with my gun!

Back to Top
The Guy View Drop Down
Platinum Member
Platinum Member
Avatar
Soup Can Guy

Joined: 18 March 2004
Status: Offline
Points: 6666 		Post Options Post Options   Thanks (0) Thanks(0)   Quote The Guy Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 1:47am
k now.

What gun do you have?
What air system?
Any recent upgrades?
My Site
Back to Top
Monk View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 23 October 2003
Location: United States
Status: Offline
Points: 6556 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Monk Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 1:48am
Tighten the screws holding the valve in place. And try it again.
Back to Top
sporx View Drop Down
Platinum Member
Platinum Member
Avatar

Joined: 03 July 2005
Location: United States
Status: Offline
Points: 5619 		Post Options Post Options   Thanks (0) Thanks(0)   Quote sporx Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 2:48am
yay! i love lemonheads!
Back to Top
FireStrorm89 View Drop Down
Member
Member
Avatar

Joined: 28 March 2005
Location: United States
Status: Offline
Points: 40 		Post Options Post Options   Thanks (0) Thanks(0)   Quote FireStrorm89 Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 11:12am

Its a 98 Custom,with standard Co2, and only upgrade I think could effect the gas is the end cap is replaced with a stock. As far as the valve screws...

Ehhhh I lost those two little guys. Thery were gone and not even screwed in the gun when I was getting these problems. I didn't think they were anything major, I forgot all about that they hold the valve in place. I would screw them in but they always would be in warped, maybe because the valve was off center in the power tube. As a result they fell out of the gun and I lost them on the field I was playing on. Maybe I'm gonna have to go pick some up.



Edited by FireStrorm89
Back to Top
†Sniper† View Drop Down
Platinum Member
Platinum Member
Avatar
In soviet Russia, paintball guns own you

Joined: 25 December 2003
Location: United States
Status: Offline
Points: 3714 		Post Options Post Options   Thanks (0) Thanks(0)   Quote †Sniper† Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 11:19am
You may want to look into getting those screws back in place. Tippmann might send you some for free.
Back to Top
The Guy View Drop Down
Platinum Member
Platinum Member
Avatar
Soup Can Guy

Joined: 18 March 2004
Status: Offline
Points: 6666 		Post Options Post Options   Thanks (0) Thanks(0)   Quote The Guy Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 12:28pm
yeah those screw keeep the valve from wobbling around. The gasline should keep forward movement to a minimum. However when the powertyube is at an angle it causes a bind with the rear bolt, dramatically slowing it down.
My Site
Back to Top
FireStrorm89 View Drop Down
Member
Member
Avatar

Joined: 28 March 2005
Location: United States
Status: Offline
Points: 40 		Post Options Post Options   Thanks (0) Thanks(0)   Quote FireStrorm89 Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 1:40pm
I just check with my local paintball dealer today and he had a spare set of valve screws. He plugged them in, they went in straight this time not worped like when I screwed them in. He shot the gun with a 20 Co2 tank and after the 5th shot the front valve screw shot out like a bullet and nearly almost hit me. He said that the right side reciever on the marker has worn out screw holes. WHAT! I used this gun like 4 times and 1 out of those times with the screws plugged in because I lost them after the first time I played. How did those screw holes get worn out?! Anyway I am going to send it to Tippmann and see if they can figure out why the valve screws keep shooting out when the gun is shot. Thats probably how I lost the screws the first time, they probably shot out of the gun when I was fighting and landed in the grass somewhere...
Back to Top
Sureshot3091 View Drop Down
Member
Member

BANNED FOR PORNO - Dad wouldnt like it

Joined: 22 February 2005
Status: Offline
Points: 1181 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Sureshot3091 Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 2:18pm
valve screw holes are stripped....$40 valve replacement is what I've heard
Back to Top
Monk View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 23 October 2003
Location: United States
Status: Offline
Points: 6556 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Monk Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 2:23pm
Man Im good. Im sorry for your loss. But after you get it back, youll be rockin'.
Back to Top
FireStrorm89 View Drop Down
Member
Member
Avatar

Joined: 28 March 2005
Location: United States
Status: Offline
Points: 40 		Post Options Post Options   Thanks (0) Thanks(0)   Quote FireStrorm89 Quote  Post ReplyReply Direct Link To This Post Posted: 03 July 2005 at 5:30pm

Its both the valve screw holes and the right side marker holes that are worn. Almost like someone put a Screw 5 times fatter than what was supposed to be put in the holes... You see that is why you are NEVER supposed to order a gun from Actionvillage. You get screwed  corny I know
Back to Top
Bruce A. Frank View Drop Down
Platinum Member
Platinum Member
Avatar
KRL Reincarnated?

Joined: 27 March 2004
Location: United States
Status: Offline
Points: 3063 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bruce A. Frank Quote  Post ReplyReply Direct Link To This Post Posted: 21 July 2005 at 1:51am

Originally posted by FireStrorm89 FireStrorm89 wrote:

I just check with my local paintball dealer today and he had a spare set of valve screws. He plugged them in, they went in straight this time not warped like when I screwed them in. He shot the gun with a 20 Co2 tank and after the 5th shot the front valve screw shot out like a bullet and nearly almost hit me. He said that the right side receiver on the marker has worn out screw holes. WHAT! I used this gun like 4 times and 1 out of those times with the screws plugged in because I lost them after the first time I played. How did those screw holes get worn out?! Anyway I am going to send it to Tippmann and see if they can figure out why the valve screws keep shooting out when the gun is shot. Thats probably how I lost the screws the first time, they probably shot out of the gun when I was fighting and landed in the grass somewhere...

Loose screws would wear those holes out of round after only a few hundred shots. The stress on the screws, as the valve is being slammed back and forth by the hammer, work them in their threads  and wear out the threads VERY quickly...the screws are steel but the valve body is aluminum which is relatively soft.

Your marker may be under warranty. Send it to Tippmann. You also need to read up on your marker. You need to learn how to disassemble and reassemble your marker. You need to understand what each of those internal parts do and how to properly torque your screws. If the screws weren't important they wouldn't have been there in the first place. Tippmann makes a very simple and rugged marker that can take outrageous abuse. Your failure to familiarize yourself with your markers function obviously exceeded that "outrageous" level.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.531 seconds.