ion
Printed From: Tippmann Paintball
Category: Paintball Equipment
Forum Name: Gun Maintenace and Repair
Forum Description: Important info for keeping your marker in top shape
URL: http://www.tippmannsports.com/forum/wwf77a/forum_posts.asp?TID=151271
Printed Date: 02 May 2024 at 9:17pm
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: ion
Posted By: pwned!!!
Subject: ion
Date Posted: 04 March 2006 at 1:36pm
| when i take the body of the ion apart, wat parts am i supposed to clean inside, do i clean the eyes? i heard u had to clean them but i thought they were electronic and had circuits and stuff in them so wouldnt it damage them if i cleaned them? |
Replies:
Posted By: pwned!!!
Date Posted: 05 March 2006 at 12:58pm
| ^ is there a seperate bit of the eyes i have to clean? |
Posted By: ionpride
Date Posted: 05 March 2006 at 1:03pm
|
you just have to dissconnect the eyes and just be very carefull with them! ------------- im the closet thing that u will come to war !!! SMART PARTS ION 3000/47 PURE ENRGY AIR DYE 03 STICKIES TEARDROP BARREL HALO B HOPPER |
Posted By: pwned!!!
Date Posted: 05 March 2006 at 1:08pm
| den do u clean them? |
Posted By: ionpride
Date Posted: 06 March 2006 at 12:35pm
|
yesh onli witha very soft small cloth ...be very gentle..... ------------- im the closet thing that u will come to war !!! SMART PARTS ION 3000/47 PURE ENRGY AIR DYE 03 STICKIES TEARDROP BARREL HALO B HOPPER |
Posted By: pwned!!!
Date Posted: 06 March 2006 at 2:55pm
| but i sounds dogey to me, ive seen the eyes and there just little bits of electronics and circuits, you just wipe it with a dry small soft cloth den? |
Posted By: pwned!!!
Date Posted: 12 March 2006 at 1:41pm
| ^ is that all u do? |
Posted By: mjicmike
Date Posted: 12 March 2006 at 3:11pm
|
"Inspect and thoroughly clean the area on the inner body where the Vision eye sits with a cotton swab. Slide the metal body into the composite outer shell, making sure that the foil sticker inside the composite body is intact and clean. This sticker helps the eye in recognizing paintballs - DO NOT REMOVE." ------------- A5 Rfs Dwg triggr Ricochet R5 8"Lapco Bigsht/14"CP Classic Palmers Stab. Lapco uni-mount DOP bullet drop fwd PMI 88/4500 Woods Flatline/14"Lapco Bigsht CMI Thunder pig reg. Remote adj. stk |
hope that helps.Posted By: spudcrazy
Date Posted: 12 March 2006 at 3:40pm
|
Dip a Q-Tip in isopropyl alcohol and clean the eye's off. Then with a dry Q-tip, wipe the eye's again. Yes it's electronics, but I think you're worrying a bit too much. Just be gentle and you'll be just fine. Tuner Tonic (found at Radio Shack) is also decent. With that, you can just spray the board and eye's down and the liquid will evaporate cleanly. I'm an Electrical Engineer and when we get done populating a board, we always take flux cleaner and spray the board down, then wash the board with alcohol and an acid brush. Usually, after that (if I'm impatient) I will blast it with air to get the excess liquid off. So don't worry. If you're careful, you won't do any damage to the eye board.... ------------- http://www.thelloydsonline.com/paintball - SPUDCRAZY http://www.oldmanmilitia.com"> 
|
pwned!!! wrote:Posted By: druidsdecendant
Date Posted: 15 March 2006 at 3:36am
|
make sure you don't bend the leads...then they would be out of alignment. Also disassemble the middle banjo and back banjo from the firing chamber. Unscrew the firing chamber in the center, remove the bolt and bolt stop (remember how you took it out!) and regrease with shocker lube, slick honey, evil puss, whatever you have that is dow33 ------------- 68 Classic Mag; PMI .68 Magnum; Maxed Stage5 Ion; M98 Scenario creation in the works; - You EPunks are all alike-all mouth until you reach the tailgate section of the field...then you "were j/j" |