Stick Feed For The 98 Custom
Printed From: Tippmann Paintball
Category: Paintball Equipment
Forum Name: Upgrades and Customizing
Forum Description: Trick it out!
URL: http://www.tippmannsports.com/forum/wwf77a/forum_posts.asp?TID=151884
Printed Date: 21 November 2025 at 3:15pm
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: Stick Feed For The 98 Custom
Posted By: Bearforce20
Subject: Stick Feed For The 98 Custom
Date Posted: 16 March 2006 at 7:44pm
| Does anybody know how i can make a ten round stick feed that will fit the 98 custon elbow? |
Replies:
Posted By: PaintballPIMPIN
Date Posted: 16 March 2006 at 7:52pm
| WHY? im confused, if you have a tubing bender or welder you can. but why? |
Posted By: OOshanis
Date Posted: 16 March 2006 at 8:59pm
|
because he wants to...it sounds like a good idea...i had an idea about that, if you want it i can send you what you need to do if you dont hav an idea yet... but yes, you can do that |
PaintballPIMPIN wrote:Posted By: Bearforce20
Date Posted: 17 March 2006 at 1:22pm
| why is a good question. The Answer is because i am a sniper. |
Posted By: DsXz
Date Posted: 17 March 2006 at 1:29pm
|
rofl snipers.... ------------- http://imageshack.us"> 
|
Posted By: Gpacker4686
Date Posted: 17 March 2006 at 1:51pm
o no i can hear the flames comeing. o well. do you want it so you want take it off and put a reg hopper on it or not? the easiest way i can think of is just getting a tube and sticking it in the elbow. if you want to get rid of the elbo all together you could drill two holes in the receiver and make them recesed(sp)(on the inside that way you won't run into the problem with them getting in the way of the paintball) then make an adapter that would fit the tubes and have the peice fit on the side of the gun using the two holes. on the end of the adapter you could have an adjustale feed neck type of thing or like a clamping feed neck that way you can just use the tubes that you store them it.
sorry how small it is but go to putfile.com/sockfootball21 and click on it, that way you can see it close up i hope this is what you were thinkin about ------------- www.putfile.com/sockfootball21 |
Posted By: FyreFly
Date Posted: 17 March 2006 at 3:07pm
|
http://x11.putfile.com/3/7512491845.jpg"> Figured I'd help you out... just click the image. ------------- 
System X NME LE WGP Orracle Cocker Tippmann A-5 E-Grip & LPK Tippmann 98C Flatline & LPK |
Posted By: Bruce A. Frank
Date Posted: 17 March 2006 at 8:31pm
|
I made these as emergency back up...when all my pods are empty. Joints on the 90 degree elbow are glued. Cap is friction fit.
|
Posted By: OOshanis
Date Posted: 17 March 2006 at 8:58pm
|
Bruce...that was my idea and i did it...i think that means i might be a genius.... na i doubt it ------------- 
|
Posted By: PaintballPIMPIN
Date Posted: 18 March 2006 at 3:40pm
| why not have a 45 degree angle so it will load that from gravity insteed of aiming ur gun down or shakin it |
Posted By: RavenGuard
Date Posted: 18 March 2006 at 4:22pm
|
yeah, try to find an elbow at like 60 degrees or a bit more, but over 45 and under 90.
------------- Tippmann A-5 Polished Internals E-Grip Ape Board JCS Blade Trigger QEV 8" Bigshot + Apex Ricochet R-5 / Tac Cap Palmers Stabilizer 68/4500 Crossfire |
Posted By: Bruce A. Frank
Date Posted: 19 March 2006 at 3:40am
|
If you are buying standard plastic pipe parts then you are limited to specific angles. You may find a 45° fitting. If you want it to gravity feed, then omit the 90° and stick the tube straight up! -------------  
|