Adjusting an Egrip.....
Printed From: Tippmann Paintball
Category: Paintball Equipment
Forum Name: Upgrades and Customizing
Forum Description: Trick it out!
URL: http://www.tippmannsports.com/forum/wwf77a/forum_posts.asp?TID=155721
Printed Date: 23 December 2025 at 9:14am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: Adjusting an Egrip.....
Posted By: Kestrell
Subject: Adjusting an Egrip.....
Date Posted: 05 June 2006 at 3:55pm
| I recently installed a new trigger but found that after adjusting it any other mode besides Semi caused the egrip to go to full auto due to mechanical bounce. Has anyone been able to adjust there egrip using the Dwell and Debounce settings to account for mechanical bounce? |
Replies:
Posted By: You Wont See Me
Date Posted: 05 June 2006 at 4:01pm
|
We need more info.... What trigger are you using? Are you using a new battery? What board do you have? ------------- A-5 E-Grip JCS Dual Trigger DOP X-CORE 8 stage x-chamber Lapco Bigshot 14" Beadblasted Optional setup: R/T Dead on Blade trigger |
Posted By: Kestrell
Date Posted: 05 June 2006 at 8:46pm
| The trigger is a Rampage Pro Trigger System from Advanced Paintball Electronics. The E-grip is the Newer WAS board equiped model and it's being powered by your standard everyday Duracell. |
Posted By: AustnOakes
Date Posted: 05 June 2006 at 8:57pm
|
o i know what you are talking about 1.hold in the trigger 2.press the power button 3.pull the trigger until the lights flickering green and orange 4.then hold the trigger in for a few seconds the led will go off 5.pull the trigger once twice three times and on the third time hold it in thats for full auto ------------- A-5 flatline was e-grip jcs deul trigger 60mm red dot scope 98 custom flatline folding stock custom valve job for quick disconnect for remote line |
Posted By: AustnOakes
Date Posted: 05 June 2006 at 8:59pm
|
if you want to know three burst or something else tell me ------------- A-5 flatline was e-grip jcs deul trigger 60mm red dot scope 98 custom flatline folding stock custom valve job for quick disconnect for remote line |
Posted By: sPAINTky
Date Posted: 05 June 2006 at 11:11pm
|
sounds like I am having the EXACT same problem. I have tried using the Debounce adjustment but so far I have it up to 45ms and still no change. For me what it does is if I fire anything more than a couple of shots or say go into full auto or turbo then the gun just takes off in full auto until I put forward pressure on the trigger.
I am running a stock a-5 w/W.A.S. E-grip and a flatline barrel. |
Posted By: AustnOakes
Date Posted: 06 June 2006 at 1:34pm
|
and that would be because the debounce is so high 45 means that when you pull the trigger it will wait 45 mil sec. until it restarts ------------- A-5 flatline was e-grip jcs deul trigger 60mm red dot scope 98 custom flatline folding stock custom valve job for quick disconnect for remote line |
Posted By: MaD_BaLlEr
Date Posted: 06 June 2006 at 8:35pm
|
in the newer was boards u have to bend the little metal thing that the trigger hits upwards
------------- A-5 W.A.S. 2 20 Oz 14 J&J coming soon x chamber stiffi barrel |
Posted By: creper5
Date Posted: 08 June 2006 at 1:30pm
i have not had this problem 
|
Posted By: cus98tom
Date Posted: 08 June 2006 at 4:14pm
| Backoff the trigger adjusment , you have it set to close . I'll bet when you dry fire (no gas) the marker it works ok. |
Posted By: cus98tom
Date Posted: 08 June 2006 at 4:27pm
| De-bounce is there to take out electrical noise from the micro-switch and/or false inputs such as bumping the marker. A de-bounce setting of 45ms means the trigger must be pressed for 45ms before a fire command is given , anything less and the marker should not shoot. shooting the marker can cause false inputs if the trigger is set to close to the micro-switch , the way the Tippmann is designed with the heavy (relative) rear bolt causes vibrations etc. initiating extra shots. |
Posted By: FyreFly
Date Posted: 08 June 2006 at 11:59pm
|
Yeah. I would agree w/ cus98tom. You need to adjust your trigger not your board. BTW, as far as I can tell, there is no point in adjusting Dwell in an E-Grip, since doing so has no effect on the actual dwell of the valve. ------------- 
System X NME LE WGP Orracle Cocker Tippmann A-5 E-Grip & LPK Tippmann 98C Flatline & LPK |