Double trigger for A5 trouble
Printed From: Tippmann Paintball
Category: Paintball Equipment
Forum Name: Upgrades and Customizing
Forum Description: Trick it out!
URL: http://www.tippmannsports.com/forum/wwf77a/forum_posts.asp?TID=164967
Printed Date: 22 December 2024 at 10:12am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com
Topic: Double trigger for A5 trouble
Posted By: bfmorgan
Subject: Double trigger for A5 trouble
Date Posted: 06 March 2007 at 1:07pm
|
I installed the double trigger on my A5. The new trigger cannot travel forward enough to re-engage the cylinder locking mechanism in a consistent fashion. I re-installed the original trigger and everything works just fine Is the part defective? Or possibly there is a trick to installing the double trigger on the A5? Thanks, |
Replies:
Posted By: an94
Date Posted: 06 March 2007 at 1:22pm
|
are you sure that the trigger is an A5 double trigger? you may have a 98c one. other than that, just put it in the grip and look to see what is causing it to bind up. sometimes it will bind up (IDK why) when you put the safety back in. just take it out & try it again. good luck oh and welcome to the forums. ------------- 1 paintball gun package=$150 1 case of paint=$50 air & entry fee=$15 lighting up newbies all day long= Priceless |
Posted By: prolitesniper
Date Posted: 08 March 2007 at 3:11pm
|
i never had that proplem, the trigger that i have feels loose and wiggles when its not on the gun, but thats it ------------- Tippmann A5 RT 16in J&J Ceramic 14in linear smartparts New BT Apex Barrel 45ci 3000psi Nitro System blade trigger 4+1pack |
Posted By: bfmorgan
Date Posted: 08 March 2007 at 9:31pm
|
I checked to see if the trigger was for the 98 and it can't fit my 98. I've tried installing it again and still the trigger must travel all the way forward and still its not engaging the cylinder catch more that 50 percent of the time. Thanks |
Posted By: MoochA-5
Date Posted: 12 March 2007 at 10:03pm
|
i had the opposite problem. when i put on the dead on double trigger i could pull and nothing. i added thin strips of electrical tape and then mine worked
|
Posted By: Black_Shadow
Date Posted: 13 March 2007 at 12:42pm
|
i wouldnt suggest this be the first thing you do, but try sanding down the trigger a little, (and i mean a little) little bit. and that might fix the problem.
------------- 98CP ACT R/T J&J Ceramic 14" Egg II w Z-Board GTA Inline X-Chamber NCStar Red-Dot Pen Spring Mod Trigger Stops Polished Internals Dye Sticky Grip 20oz Co2 w On/Off Next Up: Spimmy |
Posted By: prolitesniper
Date Posted: 15 March 2007 at 4:21am
|
ya i would say shadow has the idea; be careful though where did you get it from and online store or a shop? ------------- Tippmann A5 RT 16in J&J Ceramic 14in linear smartparts New BT Apex Barrel 45ci 3000psi Nitro System blade trigger 4+1pack |
Posted By: an94
Date Posted: 15 March 2007 at 7:05am
what do you mean by cylinder catch? do you mean R/T? take the safety out & try to see if it works? if it does its binding up on the safety. there is two small pins that the trigger is held in with. try taking out the pin that stops the trigger from swinging and see if thats it. ------------- 1 paintball gun package=$150 1 case of paint=$50 air & entry fee=$15 lighting up newbies all day long= Priceless |
bfmorgan wrote: