Print Page | Close Window

New Phenom - ASA leak

Printed From: Tippmann Paintball
Category: Paintball Equipment
Forum Name: Gun Maintenace and Repair
Forum Description: Important info for keeping your marker in top shape
URL: http://www.tippmannsports.com/forum/wwf77a/forum_posts.asp?TID=187363
Printed Date: 24 March 2026 at 5:40am
Software Version: Web Wiz Forums 12.04 - http://www.webwizforums.com


Topic: New Phenom - ASA leak
Posted By: RICKMUM
Subject: New Phenom - ASA leak
Date Posted: 18 December 2010 at 2:47am
Hey guys. I'm new here but I've been prowling the forums for a while. Before I start - yes I did use the search bar.
 
I received an X7 Phenom and a new 48/3000 Ninja tank for my birthday the other day. I screwed the tank on and had no problems firing a few test shots. After screwing/unscrewing the tank a few times I noticed a small leak coming out of the pinhole on the bottom of the ASA, and it got worse the more times I screwed the tank on.
 
It looked like the ASA was cutting the oring on the tank a little bit as there were slight cuts in it that werent there before. I replaced the oring and screwed/unscrewed the tank a few times to test; sure enough there were small cuts on the new oring and the same small leak. The leak gets worse the more times the tank is screwed/unscrewed from the marker.
 
I have now replaced the oring 3 times and am having the same problem. I googled this and found nothing. My local shop owner gave me a temporary solution (placing an oring on the ASA first then screwing on the tank) but I want a permanent fix (the oring I put in first keeps getting crushed/out of shape and doesnt help after). I have taken the grip off and inspected the orings on both ends of the copper air hose, both ends are fine. The problem doesn't seem like it should be a result of that hose however as, like I said, the leak is coming from the small pinhole on the bottom of the ASA.
 
Is this small leak normal? I don't get this issue when I screw the tank onto my 98C (there is a pinhole on that ASA too but in a different place). When I screw on my CO2 tanks to my Phenom I don't get this problem. I just can't figure it out.
 
Should I call Tippmann and ask for a new ASA? Can anyone shed some light on this??
 
Thanks in advance :)



Replies:
Posted By: Santa Claws
Date Posted: 23 December 2010 at 8:36am
I think that you should call customer support or get some kind of super nice oring
then again,mebbe its a problem w/ the c02 cartridge


-------------
What do you want for christmas little one?


Posted By: Enos Shenk
Date Posted: 28 December 2010 at 8:04am
 I would definately say call Tippmann. If the o-ring is getting cut by the threads inside the ASA that's definately a manufacturing defect.

 If you wanted to give a home fix a go, I'd say pull off the ASA and cram some steel wool in there and twist. Smooth down the crown of the ASA threads a bit. Should work for a temporary fix, just make sure you clean any steel wool bits out of there before airing it up.


-------------


Posted By: X7MAN
Date Posted: 28 December 2010 at 8:53am
But wont that void the warranty?

                            Mike


-------------
DON'T FIX IT IF IT ISN'T BROKEN!



Posted By: Enos Shenk
Date Posted: 28 December 2010 at 9:24am
 I seriously doubt it.

-------------



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.04 - http://www.webwizforums.com
Copyright ©2001-2021 Web Wiz Ltd. - https://www.webwiz.net