|
Taking off braided line...please help |
Post Reply 
|
| Author | |
AngelKiller4evr 
Member 
Joined: 26 December 2004 Location: United States Status: Offline Points: 71 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Taking off braided line...please helpPosted: 06 September 2005 at 6:58pm |
|
ok, I have found the wrench size that I need to use to take off my
braided lin, my only concern is stripping it, it has loctite on it, I
have tried to get it off, but it started to strip, I still have plenty
of sides that are fine, what tricks do you guys use while taking off
line? please help, I do not want to ruin it
 oh and I accedentally posted this in the ugrades section before, sorry about that, I got confused
|
|
|
You dont need a $1500 marker to be the best.
------- -Tippmann 98 Custom -32 Degrees quiet riot 14" barrel -BT double trigger kit -Tippmann expansion chamber -32 Degrees flame drop forward |
|
 |
|
|
bluemunky42
Member
Guested. Middle Finger post. Joined: 19 December 2004 Location: United States Status: Offline Points: 1311 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 September 2005 at 7:00pm |
|
normally i just squeeze on the pliers reeaaally tight so as to be sure not to slip at all. that's my only solution.
|
|
|
|
|
AngelKiller4evr
Member
Joined: 26 December 2004 Location: United States Status: Offline Points: 71 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 September 2005 at 7:10pm |
|
to me that would seem to strip it, what type of pliers are you talking about?
|
|
|
You dont need a $1500 marker to be the best.
------- -Tippmann 98 Custom -32 Degrees quiet riot 14" barrel -BT double trigger kit -Tippmann expansion chamber -32 Degrees flame drop forward |
|
|
|
|
Monk
Moderator Group 
Joined: 23 October 2003 Location: United States Status: Offline Points: 6556 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 September 2005 at 8:18pm |
|
Get the correct size wrench....
|
|
|
|
|
AngelKiller4evr
Member
Joined: 26 December 2004 Location: United States Status: Offline Points: 71 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 September 2005 at 9:12pm |
|
alright, I got it to work, I just used the correct size wrench, and
pliers(with a lot of man power) like bluemonkey said, thank you by the
way
|
|
|
You dont need a $1500 marker to be the best.
------- -Tippmann 98 Custom -32 Degrees quiet riot 14" barrel -BT double trigger kit -Tippmann expansion chamber -32 Degrees flame drop forward |
|
|
|
|
The Guy
Platinum Member 
Soup Can Guy Joined: 18 March 2004 Status: Offline Points: 6666 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 September 2005 at 11:40pm |
|
put the fitting in a vise, its more stable. Then turn the powertube for more leverage.
|
|
|
|
|
Enos Shenk
Platinum Member
~-o@ Joined: 10 June 2002 Location: A comfy chair Status: Offline Points: 14109 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 September 2005 at 1:43am |
|
Pliars? Jesus, dont use pliars to remove gas lines, youll tear the hell out of the hex portion.
Use the correct sized open ended wrench. Crescent wrenches work too, but its dicey unless its a good quality. Most of them will slip a bit and tear the hex portion up. |
|
|
|
|
|
|
AngelKiller4evr
Member
Joined: 26 December 2004 Location: United States Status: Offline Points: 71 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 September 2005 at 3:30pm |
|
^^ I used vice grips... it didnt hurt it one bit, but If anyone does
this, use 2 wrenches, dont take the chance, the only reason why I did
it was because I have a couple of extra hoses...
|
|
|
You dont need a $1500 marker to be the best.
------- -Tippmann 98 Custom -32 Degrees quiet riot 14" barrel -BT double trigger kit -Tippmann expansion chamber -32 Degrees flame drop forward |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
