topcocking

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

First i found a bit that would fit in this hole, the fit should be snug  .

Secure
your bolt in a vise or tape it down REALLY TIGHT if you don't have one
like me. Drill a hole on the top of the bolt I did mine farther up
(look at figure 1.)

Now
i did mine a little bit off and you can be a little off. If you drilled
in the one further back, you can just turn the inside of the bolt so
the holes meet up. But if you did father up like i did (look at figure
2.)you gotta drill in the inside part of the bolt. Now i did not drill
threw both sides of the metal bolt. I cut of the part of the bottom of
the cocking Stick. (look at figure 3.) 
I do not know if you have to do this if you drill farther back because the sear dosn't catch there. That is why i did it my way.
I am not responsible if you do this and mess up.

Now
you have to cut the receivers where the top cocking will go. I did this
my way you can do it any way though. I found a bit that would fit in
the old space for the cocking rod.

Then in the crack where the receivers meet i kept drilling along it where i knew the rod will be going.
Then filled it down till the cocking was free to move around
and then i sanded the sides for no ware and tare.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Mag-a-Man Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Strike 1 Derogatory Sexual Slur 9/22 Joined: 06 May 2005 Location: Vietnam Status: Offline Points: 1081	Post Options Post Reply Quote Mag-a-Man Report Post Thanks(0) Quote Reply Topic: topcocking Posted: 28 June 2005 at 8:57pm
	First i found a bit that would fit in this hole, the fit should be snug . Secure your bolt in a vise or tape it down REALLY TIGHT if you don't have one like me. Drill a hole on the top of the bolt I did mine farther up (look at figure 1.) Now i did mine a little bit off and you can be a little off. If you drilled in the one further back, you can just turn the inside of the bolt so the holes meet up. But if you did father up like i did (look at figure 2.)you gotta drill in the inside part of the bolt. Now i did not drill threw both sides of the metal bolt. I cut of the part of the bottom of the cocking Stick. (look at figure 3.) I do not know if you have to do this if you drill farther back because the sear dosn't catch there. That is why i did it my way. I am not responsible if you do this and mess up. Now you have to cut the receivers where the top cocking will go. I did this my way you can do it any way though. I found a bit that would fit in the old space for the cocking rod. Then in the crack where the receivers meet i kept drilling along it where i knew the rod will be going. Then filled it down till the cocking was free to move around and then i sanded the sides for no ware and tare.

You Wont See Me Members Profile Send Private Message Find Members Posts Add to Buddy List Moderator Group Found in Big Al’s underwear drawer Joined: 02 December 2003 Location: Neutral Zone Status: Offline Points: 13335	Post Options Post Reply Quote You Wont See Me Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 8:58pm
	Very nice
	A-5 E-Grip JCS Dual Trigger DOP X-CORE 8 stage x-chamber Lapco Bigshot 14" Beadblasted Optional setup: R/T Dead on Blade trigger

rossy11223 Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Joined: 02 June 2005 Location: United States Status: Offline Points: 3435	Post Options Post Reply Quote rossy11223 Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 8:59pm
	Nice

cdacda13 Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Yes, spelled secual. Joined: 12 September 2004 Location: United States Status: Offline Points: 7951	Post Options Post Reply Quote cdacda13 Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 9:02pm
	pshh, mines better For the record, you dont HAVE to drill out the inside part. Just take it out, drill the hole and turn the inter part so it points up. I know, i suck at explaining things. Edited by cdacda13

paint_master Members Profile Send Private Message Find Members Posts Add to Buddy List Member Joined: 02 February 2005 Location: United States Status: Offline Points: 21	Post Options Post Reply Quote paint_master Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 9:02pm
	impressive
	shane warren co.

cdacda13 Members Profile Send Private Message Find Members Posts Add to Buddy List Platinum Member Yes, spelled secual. Joined: 12 September 2004 Location: United States Status: Offline Points: 7951	Post Options Post Reply Quote cdacda13 Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 9:05pm
	1st step: Mill out the shells on the top. Make it so its the same size(wide and long ways). Use a hand file and dremmel. One with bolt in it. 2nd step. Drill out back bolt. Take out the inside part of the bolt. You dont need to drill the inside part, you can just flip it. Measure out where the you're going to drill. Always measure. I tried to eye it out, and missed by 1/16th of an inch Use a drill press. The regular drill dont work. The outside of the bolt is hardened. These are the directions that i PM some kid who asked for it.

Mag-a-Man Members Profile Send Private Message Find Members Posts Add to Buddy List Gold Member Strike 1 Derogatory Sexual Slur 9/22 Joined: 06 May 2005 Location: Vietnam Status: Offline Points: 1081	Post Options Post Reply Quote Mag-a-Man Report Post Thanks(0) Quote Reply Posted: 28 June 2005 at 9:26pm
	the new bolts are diffrent by the ways just to throw that into the mix