Need Help takin my A-5 Apart |
Post Reply |
Author | |
AceOfSpades98
Member Joined: 06 July 2005 Status: Offline Points: 4 |
Post Options
Thanks(0)
Posted: 28 February 2006 at 6:35pm |
I got my A-5 for christmas and Iv played with it a few times and like I tried to take it apart (not that it busted ne cuz its just a beast) but I jus wanted to be safe, and well I couldnt figure out how to get the bolt or ne thing out. I looked at the manual and I didnt rele understand it. Plz Help...
|
|
I found it hard, its hard to find oh well whatever nevermind-Kurt Cobain, Nirvana
|
|
--Red--
Member Joined: 13 February 2006 Location: United States Status: Offline Points: 377 |
Post Options
Thanks(0)
|
I need help with the same exact thing
|
|
A5 dude
Member Joined: 19 January 2006 Location: United States Status: Offline Points: 59 |
Post Options
Thanks(0)
|
Look as far as i know once you pull all the pins out and get the grip off and the back off.You then take the right size allen wrench and unscrew the allen head bolts.Once you get them unscrewed and pulled out you simply lift the reciever half up and there you go.Oh yeah if you take it apart make sure you put the ball detent in the right way or it will jam your gun.
|
|
A5 dude
|
|
cus98tom
Member Joined: 12 July 2005 Status: Offline Points: 491 |
Post Options
Thanks(0)
|
Ok, this is what I would . Go to the web site and down load the schematic for your marker and print it out, the one in the manual is to small. get a nice area to work in , get a bowl to put the small parts in. Pull all the pins out first, some may be tight so push them out with an allen key. Next take the toombstone off , this is where the hose goes into the marker . Now pull the Trigger assembly off have the safty "on" so it dost fall out and you lose it. Next loosen the 5 smaller and one larger allen screw, rotate the barrel away from you ( with the barrel in your left hand) . Remove the loosen screw the marker will now come apart. I would only go this far until you remember where everything goes. The ball latch is that orange thing at the front of the gun the mouth goes toward the barrel ">" when you tighten the screws back up dont over tighten them , hold onto the short end of the allen wrench ,this will kimit the amount of torque yoe can apply, Have Fun.
|
|
eldiablo_si
Member Joined: 19 December 2005 Location: United States Status: Offline Points: 120 |
Post Options
Thanks(0)
|
Nah, just dig in! Don't use directions! I just dug in and mine turned out just fine. I take mine apart for the hell of it now. |
|
A-5 w/ APE E-Grip, Polished Internals, 12" Lapco Bigshot, GTA X Chamber, Dead On RVA, Trinity Spring Kit, Smart Parts Inline On/Off, Smart Parts Anti-Siphons
|
|
RavenGuard
Gold Member Joined: 31 October 2005 Location: Canada Status: Offline Points: 1861 |
Post Options
Thanks(0)
|
read your manual.
|
|
Tippmann A-5
Polished Internals E-Grip Ape Board JCS Blade Trigger QEV 8" Bigshot + Apex Ricochet R-5 / Tac Cap Palmers Stabilizer 68/4500 Crossfire |
|
Santini
Member Joined: 25 December 2005 Status: Offline Points: 19 |
Post Options
Thanks(0)
|
when they are new you might have to losen the screws to remove the bolt the first time. The A-5 is user friendly as far as taking it apart and re assembling. Give it a good bop and the internals will slide out
|
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
i find it really hard to take my internals out by taking out the 4 pushpins, if u do, loosen some of the bolts a bit so that there easier to come out.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |