Tippmann Paintball Homepage
Forum Home Forum Home > Paintball Equipment > Gun Maintenace and Repair
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

Cyclone not working!!!!
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
SgtSlaughter View Drop Down
Member
Member


Joined: 19 April 2009
Location: Chesapeake VA
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SgtSlaughter Quote  Post ReplyReply Direct Link To This Post Topic: Cyclone not working!!!!
    Posted: 19 April 2009 at 8:01pm
I recently bought all the tech t upgrades and now my cyclone isnt working.  I greased all the parts up more than enough. It still isnt working. It looks like not enough air is getting to the cyclone itself so its not turning the paddles, it just kind of shakes them really fast. The power bolt(JCS Red Hot) is tilts a little also but i cant get it to stay stationary and ive tightened the screws down as much as I could get them. But i dont know if that has anything to do with it. PLEASE HELP!!! Thanks.
Back to Top
malaki View Drop Down
Member
Member


Joined: 24 October 2006
Location: AZ
Status: Offline
Points: 34 		Post Options Post Options   Thanks (0) Thanks(0)   Quote malaki Quote  Post ReplyReply Direct Link To This Post Posted: 20 April 2009 at 1:31am
was there a problem with your cyclone before getting the TechT upgrades?  Maybe stock isn't so bad.  I usually try not to get an upgrade unless I am having problems with the stock part first.
 
If you bought the entire cyclone upgrade (paddles, lightening rod, vortex, qeph) I would suggest doing a design of experiments to see what is the failing piece to the puzzle.  In other words, try each piece one at a time and see if any have a problem.  Once that is done, try combining the parts together in pairs.  You will eventually find the part that is causing the issues.
 
If it were me, I would take the QEPH off first.  I have heard quite a bit of issues with that.
Back to Top
oldpbnoob View Drop Down
Platinum Member
Platinum Member
Avatar
Not old, Not noob. May be Dave's grandma

Joined: 04 February 2008
Location: Yankee Stadium
Status: Offline
Points: 5676 		Post Options Post Options   Thanks (0) Thanks(0)   Quote oldpbnoob Quote  Post ReplyReply Direct Link To This Post Posted: 20 April 2009 at 10:43am
Take the JCS powertube out and see if you still have issues. Stock Tippmann internals seem to work best.  Also make sure you haven't over tightened anything. Whenever upgrading a marker it is good to add an item, test. Add another item, test. Making sure each upgrade works properly before adding another will help simplify troubleshooting.

Edited by oldpbnoob - 20 April 2009 at 10:44am
Back to Top
SgtSlaughter View Drop Down
Member
Member


Joined: 19 April 2009
Location: Chesapeake VA
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SgtSlaughter Quote  Post ReplyReply Direct Link To This Post Posted: 28 April 2009 at 8:17pm
Ive taken out and replaced the internals and changed them one by one and im still getting the same result. The cyclone still isnt working.
Back to Top
Nagash1959 View Drop Down
Member
Member
Avatar

Joined: 26 April 2007
Status: Offline
Points: 489 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Nagash1959 Quote  Post ReplyReply Direct Link To This Post Posted: 28 April 2009 at 9:30pm
Ok, can you manually advance it by pressing the button in, feel a click and see it spin? If not then the little metal arm isn't properly positioned.
 
Also, check to be sure that the piston has a good o-ring on it. People forget that one is there and without it the air won't act right either.
 
last thought, check the main arm that you screw the paddles onto, be sure it isn't completely round. It should be flat on one side and from the top look like a "D" almost. If it is rounded off then it will skip. 
 
Hope some of that is helpful.
98 Custom
Cyclone
Double E-Trigger
Polished Internals
Freak kit
X-chamber
CP Drop w/On/Off
Back to Top
Mellish50 View Drop Down
Member
Member


Joined: 29 April 2009
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mellish50 Quote  Post ReplyReply Direct Link To This Post Posted: 29 April 2009 at 2:24pm
Ya my Cyclone on my x7 is messed like this too, I have to manually put spin it to put a ball into my barrel. Even with C02 it doesnt spin, All my parts ARE Stock.
Back to Top
FreeEnterprise View Drop Down
Moderator Group
Moderator Group
Avatar
Not a card-carrying member of the DNC

Joined: 14 October 2008
Location: Trails Of Doom
Status: Offline
Points: 4910 		Post Options Post Options   Thanks (0) Thanks(0)   Quote FreeEnterprise Quote  Post ReplyReply Direct Link To This Post Posted: 29 April 2009 at 2:51pm
Take off the qeph... when I "upgraded" that part it ruined my cyclone.
 
Took it back off and it was fine.
 
The only techt upgrade I now have is the lighting rod. And my cyclone is not very consistant. I have to manually load it at times... I need to take it apart and mess with it, but lately, I've just been grabbing my backup a-5...
 
Typically the cause is too much grease in the part that ratchets the loader. you want that spring and the little rubber ratchet to clean and almost no grease.
 
And don't "overtighten" anything, as almost everything goes into plastic and can strip out...
They tremble at my name...
Back to Top
Mellish50 View Drop Down
Member
Member


Joined: 29 April 2009
Status: Offline
Points: 2 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Mellish50 Quote  Post ReplyReply Direct Link To This Post Posted: 29 April 2009 at 4:01pm
I didnt upgrade though, I never have. I plan on it soon tho so what else could the problem be?
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.281 seconds.