![]() |
Hinged Barrel |
Post Reply ![]() |
Page 12> |
Author | ||
>><< ![]() Gold Member ![]() ![]() <<>> Joined: 08 February 2004 Location: Byelorussian SSR Status: Offline Points: 1870 |
![]() ![]() ![]() ![]() ![]() Posted: 18 December 2005 at 7:49pm |
|
I was thinkin about this. OK we all know when we have a barrel break the next balls you shoot go everywhere and that really hurts your accuracy and your waistin balls really. But ok a hinge about an inch into the barrel and swings down when you press the button that is located at the top or bottom of the barrel and the barrel swings down allowing you to ram a squeegee of your choice in there and then popping the barrel back into placeand your back in action. This whole action could take as little as 10 seconds if you use a staright squeegee just ram it in take it out pop the barrel and your done clean barrel and all. You would have to make sure the barrel makes a good fit when you put back in place so it doesn't screw up anything. |
||
![]() |
||
![]() |
||
brihard ![]() Platinum Member ![]() ![]() Strike 1 - Making stuff up Joined: 05 September 2004 Location: Canada Status: Offline Points: 10155 |
![]() ![]() ![]() ![]() ![]() |
|
No. Just unscrew the barrel.
A hinge would create irregularities in the barrel that would be bad for accuracy. |
||
"Abortion is not "choice" in America. It is forced and the democrats are behind it, with the goal of eugenics at its foundation."
-FreeEnterprise, 21 April 2011. Yup, he actually said that. |
||
![]() |
||
>><< ![]() Gold Member ![]() ![]() <<>> Joined: 08 February 2004 Location: Byelorussian SSR Status: Offline Points: 1870 |
![]() ![]() ![]() ![]() ![]() |
|
and in a speedball game you don't have time to uncrew your barrel. |
||
![]() |
||
![]() |
||
TruePaintballer ![]() Platinum Member ![]() ![]() Strike 1 - Spam 11-19 Joined: 03 July 2004 Location: Canada Status: Offline Points: 4083 |
![]() ![]() ![]() ![]() ![]() |
|
it has potential...would take a lot of work tho
|
||
![]() |
||
WGP guy2 ![]() Platinum Member ![]() ![]() I play the Bag Pipes Joined: 23 September 2005 Location: 17h 45m 40.04s Status: Offline Points: 2585 |
![]() ![]() ![]() ![]() ![]() |
|
Thats not so easy when you have cocker threads, its 8.5 turns and you have the pnue host pushing the barrel making it worse. |
||
![]() |
||
Monk ![]() Moderator Group ![]() ![]() Joined: 23 October 2003 Location: United States Status: Offline Points: 6556 |
![]() ![]() ![]() ![]() ![]() |
|
I think Id rather have a hinged feedneck. But thats still cool.
|
||
![]() |
||
Tiger Stripe ![]() Member ![]() Strike 2,Troll w/Account:: LERHIT1/21/06 Joined: 19 December 2005 Location: United Kingdom Status: Offline Points: 326 |
![]() ![]() ![]() ![]() ![]() |
|
*first post* cool idea but i think unscrewing the barrel would be much easyer lee |
||
<<Sig much too large>>
|
||
![]() |
||
UV Halo ![]() Member ![]() ![]() Joined: 19 August 2004 Location: United States Status: Offline Points: 229 |
![]() ![]() ![]() ![]() ![]() |
|
A hinge in the barrel would introduce a seam that could negatively impact accuracy. Barrel sleaves and such work because they can be designed concentric. A hinged connection cannot operate off a simple hinge. You'd need a hinge more like a car door (two pins), and the tolerances would need to be too tight to make it work.
However, you could hinge the body (think like the early Line SI semi-autos) since the paintball would not touch the body, and you don't need to worry as much about a seam line. That way, you could leave the barrel in place, and still be able to swap out barrels. |
||
M98C- W/QwkStrpCut
Comp Air & Palmer Fatty Stab Gas-Thru Stock Lapco Sight Rail W/ADCO 30MM EDOT Qloader W/ CMS Freak SS W/Stif-Tip * Flatline * Armson Stealth |
||
![]() |
||
Styro Folme ![]() Platinum Member ![]() Strike 1 - Rules 1 and 2 Joined: 28 February 2005 Location: United States Status: Offline Points: 8086 |
![]() ![]() ![]() ![]() ![]() |
|
i think it's a great idea. would be difficult to do, but it would pay off.
|
||
X
|
||
![]() |
||
merc ![]() Platinum Member ![]() ![]() American Scotchy Joined: 10 June 2002 Location: VA, USA Status: Offline Points: 7112 |
![]() ![]() ![]() ![]() ![]() |
|
sheridan jackel has a hinged barrel. they just use a taper to make sure its not off.
|
||
saving the world, one warship at a time.
|
||
![]() |
||
The Guy ![]() Platinum Member ![]() ![]() Soup Can Guy Joined: 18 March 2004 Status: Offline Points: 6666 |
![]() ![]() ![]() ![]() ![]() |
|
did you ever wonder why a straight shot has the springy part? Press down on the swap end, shove the rubber end down you barrel, release and pull out. |
||
![]() |
||
>><< ![]() Gold Member ![]() ![]() <<>> Joined: 08 February 2004 Location: Byelorussian SSR Status: Offline Points: 1870 |
![]() ![]() ![]() ![]() ![]() |
|
I don't have a straight shot squeegee or seen one so i don't what your talkin about. Actually i have seen on but i don't remember a springy thing. |
||
![]() |
||
![]() |
||
The Guy ![]() Platinum Member ![]() ![]() Soup Can Guy Joined: 18 March 2004 Status: Offline Points: 6666 |
![]() ![]() ![]() ![]() ![]() |
|
but anyway, youd be better off if the hinger was actually built into the gun.
|
||
![]() |
||
sneaky_sniper ![]() Gold Member ![]() ![]() Guested - inappropriate link 01/13 Joined: 05 September 2005 Location: United States Status: Offline Points: 1325 |
![]() ![]() ![]() ![]() ![]() |
|
i want a bolt action pb gun but it aint gunna happen... im not really sure what this has to do with it, but o well...
|
||
[IMG]http://i26.photobucket.com/albums/c128/sneaky_sniper/Invader_Zim.jpg">
|
||
![]() |
||
Mr. Spiffy ![]() Member ![]() ![]() Joined: 18 January 2003 Location: United States Status: Offline Points: 5 |
![]() ![]() ![]() ![]() ![]() |
|
Why not make a barrel adaptor that has the hinge? You can screw it into the gun and the barrel into the adaptor. The adaptor has hinges that allow the barrel to swing out from the marker for quick cleaning. No mods needed for the marker or the barrel
![]() |
||
Missing: 2nd star and 960+ posts to my name.
-Another victim of the system. |
||
![]() |
||
sneaky_sniper ![]() Gold Member ![]() ![]() Guested - inappropriate link 01/13 Joined: 05 September 2005 Location: United States Status: Offline Points: 1325 |
![]() ![]() ![]() ![]() ![]() |
|
i like it...and you can undo it without any paintballs falling out because the hinge is past the ball latchy thing
|
||
[IMG]http://i26.photobucket.com/albums/c128/sneaky_sniper/Invader_Zim.jpg">
|
||
![]() |
||
curby972 ![]() Member ![]() ![]() Joined: 06 November 2005 Location: United States Status: Offline Points: 143 |
![]() ![]() ![]() ![]() ![]() |
|
i think the hinged barrel could work just have some oring in there some where to keep it connected good to the other piece and so it keeps a good seal.
|
||
![]() |
||
Da dude ![]() Member ![]() ![]() Joined: 27 December 2005 Location: United States Status: Offline Points: 20 |
![]() ![]() ![]() ![]() ![]() |
|
all u got to do is w8 till its invented and buy it
><> go fish ------------- 98c dye sticky grips 16'' j&j barrel |
||
![]() |
||
BearClaw ![]() Moderator Group ![]() ![]() Joined: 19 August 2003 Location: Canada Status: Offline Points: 2102 |
![]() ![]() ![]() ![]() ![]() |
|
Dang good idea one of the few in this section of the forum LOL.
The Carbines alow the whole fron grip to move forward so use of a wire squegy can be used through the breach similare to the 98c but this takes alot more than a break away might take. Wish i still had my gramps olds Savage 94 12 gauge single shot gun to see how it worked with the break away. |
||
AGD 68 Automag
Azodin KPII Sheridan PGP2K Tippmann Crossover XVR Tippmann ProCarbine Tippmann SL68-II Tippmann TiPX |
||
![]() |
||
>><< ![]() Gold Member ![]() ![]() <<>> Joined: 08 February 2004 Location: Byelorussian SSR Status: Offline Points: 1870 |
![]() ![]() ![]() ![]() ![]() |
|
If i had any idea on how to make this i would cause i think alot of people would buy and it'd help alot. Maybe this will be my first patent??
|
||
![]() |
||
![]() |
Post Reply ![]() |
Page 12> |
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |