|
gun will not stop firing |
Post Reply 
|
| Author | |
barnell 
Member 
Joined: 23 April 2006 Location: United States Status: Offline Points: 4 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: gun will not stop firingPosted: 22 October 2006 at 7:26am |
|
when i fire my gun the hammer some times just keeps firing and will not stop unless stop it with my hand. any ideas on how to fix it?
|
|
 |
|
|
TIPPY98ACT
Member
Joined: 23 August 2006 Location: United States Status: Offline Points: 332 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 October 2006 at 8:31am |
|
What gun do you have? If you have a 98ACT Check the news section on the home page. I have posted many times about the sear spring update. Also do you use CO2? Check to make sure your tank isn't getting low.
|
|
|
|
|
iceman1186
Gold Member 
Joined: 09 October 2002 Location: United States Status: Offline Points: 1036 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 October 2006 at 10:18am |
|
Check to see if your sear/rear bolt are worn down. If they are worn, replace. Also make sure that the valve screws on the side of the marker are tight.
|
|
|
|
|
|
|
tippmannsnyper9
Member
Joined: 14 June 2006 Location: Canada Status: Offline Points: 37 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 October 2006 at 9:30pm |
|
are you using an E-grip with a WAS board?
|
|
|
|
|
carl_the_sniper
Platinum Member 
Strike 1 - 7/29, Bad Linky Joined: 08 April 2006 Location: Canada Status: Offline Points: 11259 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 October 2006 at 10:36pm |
|
polish your internals with a grinder?
|
|
|
<just say no to unnecessarily sexualized sigs>
|
|
|
|
|
barnell
Member
Joined: 23 April 2006 Location: United States Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 October 2006 at 2:54pm |
|
I have a 98 custom with an expansion chamber and a response trigger. The response trigger has been disconnected. It happens mostly when the co2 tank is full. The internals have been cleaned and oiled. The marker is not very old maybe 6 months. I just tried replacing most of the o-rings and one of the springs for the trigger but have not tested it yet. Thank for the help so far any more suggestion will be great
|
|
|
|
|
Rambino
Platinum Member
I am even less fun in person Joined: 15 August 2002 Location: United States Status: Offline Points: 16593 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 October 2006 at 3:26pm |
|
Do you have a stock or an RVA? Have you changed out any of the springs recently, or added a straw mod or other trigger mods?
|
|
|
[IMG]http://i38.tinypic.com/aag8s8.jpg">
|
|
|
|
|
barnell
Member
Joined: 23 April 2006 Location: United States Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 October 2006 at 9:37pm |
|
Do you have a stock or an RVA? Have you changed out any of the springs recently, or added a straw mod or other trigger mods? what do you mean stock or ARV? I only have the 2 mods, listed above, i change the shear spring in hope of fixing the problem but i have not tested it since then. Edited by barnell - 23 October 2006 at 9:52pm |
|
|
|
|
iceman1186
Gold Member
Joined: 09 October 2002 Location: United States Status: Offline Points: 1036 |
Post Options
Thanks(0)
Quote Reply
Posted: 23 October 2006 at 11:02pm |
|
|
|
|
|
|
|
|
TIPPY98ACT
Member
Joined: 23 August 2006 Location: United States Status: Offline Points: 332 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 October 2006 at 12:27am |
|
Have you read about the sear spring update yet? If your gun left the factory with a bad one, it's likely the sear is worn from use with the R/T. If your serial number falls in the range, they will send all the new parts to fix ( new sear, rear bolt, new updated spring, and o-rings) for free! Again look for 98 custom service update in the news section on the homepage. Or call Tippmann.
Edited by TIPPY98ACT - 24 October 2006 at 1:25am |
|
|
|
|
barnell
Member
Joined: 23 April 2006 Location: United States Status: Offline Points: 4 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 October 2006 at 4:30pm |
|
Have you read about the sear spring update yet? If your gun left the factory with a bad one, it's likely the sear is worn from use with the R/T. If your serial number falls in the range, they will send all the new parts to fix ( new sear, rear bolt, new updated spring, and o-rings) for free! Again look for 98 custom service update in the news section on the homepage. Or call Tippmann. Yeah i just read the about that today and it sound like the problem. Thank everyone for the help |
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
iceman1186 wrote: