ion |
Post Reply |
Author | |
druidsdecendant
Member Strike 1 - Language 9/3 Joined: 21 July 2005 Location: United States Status: Offline Points: 260 |
Post Options
Thanks(0)
Posted: 15 March 2006 at 3:36am |
make sure you don't bend the leads...then they would be out of alignment. Also disassemble the middle banjo and back banjo from the firing chamber. Unscrew the firing chamber in the center, remove the bolt and bolt stop (remember how you took it out!) and regrease with shocker lube, slick honey, evil puss, whatever you have that is dow33
|
|
68 Classic Mag; PMI .68 Magnum; Maxed Stage5 Ion; M98 Scenario creation in the works; - You EPunks are all alike-all mouth until you reach the tailgate section of the field...then you "were j/j"
|
|
spudcrazy
Member Joined: 14 July 2005 Location: United States Status: Offline Points: 363 |
Post Options
Thanks(0)
|
Dip a Q-Tip in isopropyl alcohol and clean the eye's off. Then with a dry Q-tip, wipe the eye's again. Yes it's electronics, but I think you're worrying a bit too much. Just be gentle and you'll be just fine. Tuner Tonic (found at Radio Shack) is also decent. With that, you can just spray the board and eye's down and the liquid will evaporate cleanly. I'm an Electrical Engineer and when we get done populating a board, we always take flux cleaner and spray the board down, then wash the board with alcohol and an acid brush. Usually, after that (if I'm impatient) I will blast it with air to get the excess liquid off. So don't worry. If you're careful, you won't do any damage to the eye board.... |
|
mjicmike
Gold Member Joined: 20 November 2005 Location: United States Status: Offline Points: 1039 |
Post Options
Thanks(0)
|
"Inspect and thoroughly clean the area on the inner body where the Vision eye sits with a cotton swab. Slide the metal body into the composite outer shell, making sure that the foil sticker inside the composite body is intact and clean. This sticker helps the eye in recognizing paintballs - DO NOT REMOVE." hope that helps. |
|
A5 Rfs Dwg triggr
Ricochet R5 8"Lapco Bigsht/14"CP Classic Palmers Stab. Lapco uni-mount DOP bullet drop fwd PMI 88/4500 Woods Flatline/14"Lapco Bigsht CMI Thunder pig reg. Remote adj. stk |
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
^ is that all u do?
|
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
but i sounds dogey to me, ive seen the eyes and there just little bits of electronics and circuits, you just wipe it with a dry small soft cloth den?
|
|
ionpride
Member Strike 1 - F-Bomb 2/28 Joined: 20 February 2006 Location: United Kingdom Status: Offline Points: 359 |
Post Options
Thanks(0)
|
yesh onli witha very soft small cloth ...be very gentle.....
|
|
im the closet thing that u will come to war !!!
SMART PARTS ION 3000/47 PURE ENRGY AIR DYE 03 STICKIES TEARDROP BARREL HALO B HOPPER |
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
den do u clean them?
|
|
ionpride
Member Strike 1 - F-Bomb 2/28 Joined: 20 February 2006 Location: United Kingdom Status: Offline Points: 359 |
Post Options
Thanks(0)
|
you just have to dissconnect the eyes and just be very carefull with them!
|
|
im the closet thing that u will come to war !!!
SMART PARTS ION 3000/47 PURE ENRGY AIR DYE 03 STICKIES TEARDROP BARREL HALO B HOPPER |
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
^ is there a seperate bit of the eyes i have to clean?
|
|
pwned!!!
Member Strike 1 - Rudeness 6/30 Joined: 13 January 2006 Status: Offline Points: 443 |
Post Options
Thanks(0)
|
when i take the body of the ion apart, wat parts am i supposed to clean inside, do i clean the eyes? i heard u had to clean them but i thought they were electronic and had circuits and stuff in them so wouldnt it damage them if i cleaned them?
Edited by pwned!!! - 05 March 2006 at 9:18am |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |