|
Stick Feed For The 98 Custom |
Post Reply 
|
| Author | |
Bearforce20 
Member 
Joined: 13 July 2004 Location: United States Status: Offline Points: 15 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Stick Feed For The 98 CustomPosted: 16 March 2006 at 7:44pm |
|
Does anybody know how i can make a ten round stick feed that will fit the 98 custon elbow?
|
|
 |
|
|
PaintballPIMPIN
Gold Member 
STRIKE 1 - NO SELLING ON THE FORUM 3/31 Joined: 08 February 2006 Location: United States Status: Offline Points: 1055 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 March 2006 at 7:52pm |
|
WHY? im confused, if you have a tubing bender or welder you can. but why?
|
|
|
|
|
OOshanis
Member
Joined: 02 February 2006 Location: United States Status: Offline Points: 511 |
Post Options
Thanks(0)
Quote Reply
Posted: 16 March 2006 at 8:59pm |
|
because he wants to...it sounds like a good idea...i had an idea about that, if you want it i can send you what you need to do if you dont hav an idea yet... but yes, you can do that |
|
|
|
|
Bearforce20
Member
Joined: 13 July 2004 Location: United States Status: Offline Points: 15 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 1:22pm |
|
why is a good question. The Answer is because i am a sniper.
|
|
|
|
|
DsXz
Gold Member
Guested 3 strikes 10/25 Joined: 07 February 2006 Location: United States Status: Offline Points: 1721 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 1:29pm |
|
rofl snipers....
|
|
|
|
|
|
|
Gpacker4686
Member
Strike 1 - Language, 9/22 Joined: 12 November 2002 Location: United States Status: Offline Points: 566 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 1:51pm |
|
o no i can hear the flames comeing. o well. do you want it so you want take it off and put a reg hopper on it or not? the easiest way i can think of is just getting a tube and sticking it in the elbow. if you want to get rid of the elbo all together you could drill two holes in the receiver and make them recesed(sp)(on the inside that way you won't run into the problem with them getting in the way of the paintball) then make an adapter that would fit the tubes and have the peice fit on the side of the gun using the two holes. on the end of the adapter you could have an adjustale feed neck type of thing or like a clamping feed neck that way you can just use the tubes that you store them it.
sorry how small it is but go to putfile.com/sockfootball21 and click on it, that way you can see it close up i hope this is what you were thinkin about |
|
|
www.putfile.com/sockfootball21
|
|
|
|
|
FyreFly
Gold Member
Joined: 15 November 2003 Location: United States Status: Offline Points: 1383 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 3:07pm |
 Figured I'd help you out... just click the image.Edited by FyreFly - 17 March 2006 at 3:08pm |
|
System X NME LE WGP Orracle Cocker Tippmann A-5 E-Grip & LPK Tippmann 98C Flatline & LPK |
|
|
|
|
Bruce A. Frank
Platinum Member 
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 8:31pm |
|
I made these as emergency back up...when all my pods are empty. Joints on the 90 degree elbow are glued. Cap is friction fit.
Edited by Bruce A. Frank - 17 March 2006 at 8:35pm |
|
|
|
|
OOshanis
Member
Joined: 02 February 2006 Location: United States Status: Offline Points: 511 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 March 2006 at 8:58pm |
|
Bruce...that was my idea and i did it...i think that means i might be a genius.... na i doubt it |
|
|
|
|
|
|
PaintballPIMPIN
Gold Member
STRIKE 1 - NO SELLING ON THE FORUM 3/31 Joined: 08 February 2006 Location: United States Status: Offline Points: 1055 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 March 2006 at 3:40pm |
|
why not have a 45 degree angle so it will load that from gravity insteed of aiming ur gun down or shakin it
|
|
|
|
|
RavenGuard
Gold Member
Joined: 31 October 2005 Location: Canada Status: Offline Points: 1861 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 March 2006 at 4:22pm |
|
yeah, try to find an elbow at like 60 degrees or a bit more, but over 45 and under 90.
|
|
|
Tippmann A-5
Polished Internals E-Grip Ape Board JCS Blade Trigger QEV 8" Bigshot + Apex Ricochet R-5 / Tac Cap Palmers Stabilizer 68/4500 Crossfire |
|
|
|
|
Bruce A. Frank
Platinum Member
KRL Reincarnated? Joined: 27 March 2004 Location: United States Status: Offline Points: 3063 |
Post Options
Thanks(0)
Quote Reply
Posted: 19 March 2006 at 3:40am |
|
If you are buying standard plastic pipe parts then you are limited to specific angles. You may find a 45° fitting. If you want it to gravity feed, then omit the 90° and stick the tube straight up! |
|
 
|
|
|
|
|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
PaintballPIMPIN wrote:
