Tippmann Paintball Homepage
Forum Home Forum Home > Tippmann Paintball > Marker Gallery
  New Posts New Posts
  FAQ FAQ  Forum Search   Register Register  Login Login

new halo b...oh and my ion..again

 Post Reply Post Reply Page  <12
Author
Message
blackdog144 View Drop Down
Platinum Member
Platinum Member
Avatar

Joined: 23 June 2005
Location: United States
Status: Offline
Points: 3786
Post Options Post Options   Thanks (0) Thanks(0)   Quote blackdog144 Quote  Post ReplyReply Direct Link To This Post Posted: 09 August 2006 at 2:08am
this friday before i paintball im going to buy a feedneck...but ya it wont fit in my custom pro...



Back to Top
meteora View Drop Down
Gold Member
Gold Member
Avatar

Joined: 28 December 2003
Location: United States
Status: Offline
Points: 1892
Post Options Post Options   Thanks (0) Thanks(0)   Quote meteora Quote  Post ReplyReply Direct Link To This Post Posted: 09 August 2006 at 2:15am
How to change the modes:


"Programing:
· To adjust any of the settings on the circuit board, you must remove the left side of the grips and push the programming button once.
· There are two additional LEDs located under the grips as well (yellow and red). When you enter programming mode, one of the LEDs will light up, signifying you're in programming mode.
· Pushing the programming button will cycle through the six adjustment modes, each with its own LED color/pattern:
Solid yellow - Dwell up
Solid red - Dwell down
Single blink yellow - Recharge up
Single blink red - Recharge down
Double blink yellow - Fire mode up
Double blink red - Fire mode down

Adjusting the board is easy to do.
· First, select which adjustment mode you want by the LED pattern and color. For example, to increase dwell select solid yellow.
· The power button is used to adjust the setting. It will adjust it by one interval in whatever direction you sleecred (up or down).
· Each time you push the power button, the opposite color LED will blink once to signify it has been adjusted one time.
· As you push the power button, at some point the LED will stop blinking; this signifies you have reached the maximum/minimum setting.
· To exit the programming mode, push the trigger once. After pushing the trigger, turn the board off to save the settings. If you pull the battery, the new setting will revert back to whatever it was last set to.

Fire Mode: LED double blink
The stock board is equipped with four(4) fire modes, in this order from highest to lowest:
Fullyautomatic
Three-shot burst
Rebound (ramping)
Semiauto"

Taken from zds paintball.


GUN WHORE
XTC
Back to Top
blackdog144 View Drop Down
Platinum Member
Platinum Member
Avatar

Joined: 23 June 2005
Location: United States
Status: Offline
Points: 3786
Post Options Post Options   Thanks (0) Thanks(0)   Quote blackdog144 Quote  Post ReplyReply Direct Link To This Post Posted: 09 August 2006 at 3:27pm
ya the guy at my locals pb shop did it for me, but he didnt say how to change modes as in from semi to full auto and whatnot...so im still some what confused on that part...



Back to Top
Hairball!!! View Drop Down
Moderator Group
Moderator Group

Strike #4

Joined: 12 June 2002
Location: Snow (again)
Status: Offline
Points: 6941
Post Options Post Options   Thanks (0) Thanks(0)   Quote Hairball!!! Quote  Post ReplyReply Direct Link To This Post Posted: 10 August 2006 at 12:59am
I thought that said frog
Back to Top
blackdog144 View Drop Down
Platinum Member
Platinum Member
Avatar

Joined: 23 June 2005
Location: United States
Status: Offline
Points: 3786
Post Options Post Options   Thanks (0) Thanks(0)   Quote blackdog144 Quote  Post ReplyReply Direct Link To This Post Posted: 10 August 2006 at 2:22am
thats what i thought first but ya not anymore...



Back to Top
bvsnbtthd View Drop Down
Member
Member
Avatar

Joined: 09 August 2006
Location: United States
Status: Offline
Points: 26
Post Options Post Options   Thanks (0) Thanks(0)   Quote bvsnbtthd Quote  Post ReplyReply Direct Link To This Post Posted: 10 August 2006 at 2:35am
save the $. sand it.
stick it 2 da mann
Back to Top
blackdog144 View Drop Down
Platinum Member
Platinum Member
Avatar

Joined: 23 June 2005
Location: United States
Status: Offline
Points: 3786
Post Options Post Options   Thanks (0) Thanks(0)   Quote blackdog144 Quote  Post ReplyReply Direct Link To This Post Posted: 10 August 2006 at 11:24am
my friend had a good idea..yesterday when he came over we didnt sand my halo b, we sanded the inside of the feedneck, it fits good now...but im still getting a new feedneck..



Back to Top
Boo bear 2 View Drop Down
Member
Member
Avatar

Joined: 10 August 2006
Location: Canada
Status: Offline
Points: 64
Post Options Post Options   Thanks (0) Thanks(0)   Quote Boo bear 2 Quote  Post ReplyReply Direct Link To This Post Posted: 16 August 2006 at 5:35pm

nice

 

Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.04
Copyright ©2001-2021 Web Wiz Ltd.

This page was generated in 0.453 seconds.